Mosaics¶
The viewer shows a dataset's mosaics, opened with View mosaics on its card or from the navigation pane.
A preview, not an orthomosaic
The mosaics are a quick preview to help the analysis: each frame is placed by its own position and the camera's angles. They are no replacement for an orthomosaic made by photogrammetry, such as WebODM's (ODM's), which matches the frames to each other and models the ground from them. Measure distances and areas, and place things on a map, from such an orthomosaic when they must be exact.

The tabs¶
Each tab's tooltip says what it shows.
- Mosaic: each pixel is one frame's own temperature, as the frames were converted.
- Harmonized: normalized, with one ambient and reflected temperature for every frame, and each frame's offset against its neighbours removed (the camera's drift between recalibrations), so the seams don't show as bands.
- Source frame: which frame each pixel comes from (the one that saw it closest to straight down), with a line along each seam between the frames (in the mosaic report too).
- View angle: how far from straight down each pixel was seen, in degrees.
- Visual: the visual mosaic, when the dataset has one: the visual camera's images, each placed where its thermal frame is. Pointer info gives the Mosaic tab's temperatures, and a click opens the frames that saw the spot.
- WebODM and Heights: an orthophoto and a surface model brought back from WebODM.
The dataset of a flight of visual images only has the Visual tab alone, with no palette or temperatures. A click on a spot, or a spot drawn, opens the visual frames that saw it, each shown as it was taken with the spot marked, the one the mosaic took it from first (the frame that saw it closest to straight down). A line, area, box or circle drawn is measured for its size. The side panel lists the saved measurements and the flight's findings, and The mosaic says how it was laid out: the frames used, the camera's boresight and lens distortion, the surface's heights and how closely overlapping frames agree. Its header has Compare with…, Mosaic report and Rebuild mosaic.
An imported dataset¶
A dataset imported from WebODM is shown as it holds:
- An orthophoto of temperatures on the WebODM tab, with its palette, range, Pointer info, measuring and findings as for any mosaic of temperatures.
- An orthophoto of colours on the Visual tab, as the visual mosaic of a flight of visual images only is: a click opens the photos that saw the spot, and a line or an area is measured for its size.
- Its DSM on the Heights tab, beside either. Beside a Visual tab, Heights loads the page again on the temperatures' viewer, and Visual brings it back.
The header has Open in WebODM (the task it came from, in WebODM's dashboard, for one imported from a task), Compare with…, Export… (on the WebODM and Heights tabs) and Mosaic report, with no Frames or Build mosaics; The mosaic in the side panel says where it came from: the WebODM project and task, when the task was made, from how many images, how long WebODM took, and the DSM (or the files' names).
The frames of a spot¶
ODM doesn't record which photo each pixel of its orthophoto comes from, so the flight's photos that saw a spot or an area are found from the task's cameras instead: where WebODM placed each photo and how its lens sees, with the spot at the height of the DSM (or, without one, of the ground under the photos). A click on the WebODM or Visual tab opens them, as does a measured spot's or area's Source frames; the window lists them, the most nadir first, marked in the mosaic as the one most likely used, and a finding keeps them as on any mosaic. A thermal frame is measured with the settings of the dataset its task was sent from, or with its own parameters for a task made in WebODM; an orthophoto of colours shows its photos as they were taken. Frames have no Open frame: an imported dataset has no frames page.
- Imported from a task: the cameras come with the orthophoto. One imported before they did, or while WebODM couldn't give them, fetches them the first time a spot's frames are asked for; while WebODM can't be reached, the window says so, and the spot can still be kept as a finding.
- Imported from a file: the frames are known only when the task's
shots.geojsonandcameras.jsoncame with it.
The photos must be the flight's own: a photo is matched by its name, or by the name of the TIFF it was sent to WebODM
as (DJI_…_T_temp_c.tiff for DJI_…_T.JPG). Like a mosaic's frames, a photo is listed where it looked towards the
spot, even if something stood in the way.
The viewer opens on Mosaic, or on Harmonized when the frames disagree (their offsets against their neighbours spanning more than 3 °C over the middle 90% of them), with a notice saying so. A link that names a tab opens that one.
Under the mosaic is a street map or satellite imagery, chosen with the switch at the top right of the map (see The maps under the mosaics).
The side panel¶
The panel has, from the top:
- View: the palette, the temperature range, Image (brightness and contrast, gamma, sharpening and Banded) and Isotherm. They are redrawn as their sliders are dragged. The colour scale is labelled with its range's ends, and the line straight under it gives the mosaic's own lowest and highest temperatures.
Under the range's fields is a cross of buttons. Its centre, Auto, sets the range to the mosaic's 2nd to 98th percentile. Its arrows step the range: ◀ Narrow and ▶ Widen take 10% off its span or add 10%, half at each end, and ▼ Lower and ▲ Raise move both ends by 10% of the span (a click on the name does the same). Neither end goes past the mosaic's own lowest and highest temperatures: an end that reaches one stays there while the other moves on, so the span shrinks. An arrow that would change nothing is greyed out. - Then Pointer info (the values under the cursor), Parameters and This mosaic. - Then the saved measurements and the findings. - About.
On a first visit Image, Parameters, This mosaic and The mosaic start folded, and each section then stays as it was left.
Banded¶
Banded, in Image on a temperature tab, draws the temperatures in bands a Bandwidth wide (1 to 10 degrees of your unit, 5 at first), a band starting at every multiple of it (70, 75, 80 °F):
- Stepped: each band in one colour, the palette's colour at its middle, so that each colour is a span of temperatures.
- Banded: the palette as it is, with every other band darker, so that the bands show as stripes across it.

The colour scale shows the bands too. They change how the temperatures are drawn, never the temperatures; the link, the PNG exports and the mosaic report keep them.
Pointer info¶
Pointer info gives the values under the cursor. A click keeps them and outlines the frame there, and Open frame then opens that frame on the frame page; Escape or a second click on that frame lets go of it.
Temperature On Pointer, in Pointer info's heading, shows the temperature under the cursor in a small tip beside it, once the cursor rests, and goes on following the cursor while a click keeps Pointer info's values. There is no tip where Pointer info has no temperature, such as off the mosaic or where it has no data. It is off until ticked, and then stays ticked in this browser, on the frame page too.
Delta T Around Pointer, at the top of Pointer info, compares the pixel under the cursor with the pixels around it: a thin circle outlines them on the map, and its Radius slider sets how far it reaches on the ground (0.25 m, then 0.5 to 10 m). Under the values at the cursor come the circle's mean, its lowest and highest temperature, the number of pixels in it and ΔT, the pixel's temperature minus the circle's mean (the pixel itself left out of the circle). The pixels the circle's outline touches count as inside it. Once the cursor rests, a small tip just right of the circle shows its ΔT too. While a click keeps Pointer info's values, the circle stays on the point clicked, with its tip, and a new radius measures it again. It is on the temperature tabs only (not on Visual, Source frame or Heights), and the box and the radius stay as they were left in this browser.
From the viewer¶
The viewer's header has Frames (the frames explorer), Compare with… (the compare page), Export… (the mosaic as shown, with its saved measurements and colour scale, or whole, at full resolution: see Exports), Mosaic report (see Reports) and Rebuild mosaics.
Rebuild mosaics builds the new mosaics beside the last ones, which stay on show until the new ones replace them, so the disk needs room for both for that time. If the rebuild fails or is canceled, the last ones are kept.