smartctl 7.2 2020-12-30 r5155 [x86_64-linux-6.8.0-110-generic] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     HGST Travelstar 5K1000
Device Model:     HGST HTS541010A9E680
Serial Number:    JA1009CR2VLLMP
LU WWN Device Id: 5 000cca 79ae8467b
Firmware Version: JA0OA710
User Capacity:    1,000,204,886,016 bytes [1.00 TB]
Sector Sizes:     512 bytes logical, 4096 bytes physical
Rotation Rate:    5400 rpm
Form Factor:      2.5 inches
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ACS-2, ATA8-ACS T13/1699-D revision 6
SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Wed Jul  8 10:49:57 2026 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM level is:     254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82)	Offline data collection activity
					was completed without error.
					Auto Offline Data Collection: Enabled.
Self-test execution status:      ( 121)	The previous self-test completed having
					the read element of the test failed.
Total time to complete Offline 
data collection: 		(   45) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 ( 234) minutes.
SCT capabilities: 	       (0x003d)	SCT Status supported.
					SCT Error Recovery Control supported.
					SCT Feature Control supported.
					SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR-K   067   067   062    -    390267333
  2 Throughput_Performance  P-S--K   198   100   040    -    124
  3 Spin_Up_Time            PO---K   176   100   033    -    1
  4 Start_Stop_Count        -O--CK   100   100   000    -    468
  5 Reallocated_Sector_Ct   PO--CK   100   100   005    -    720 (0 45)
  7 Seek_Error_Rate         POSR-K   100   100   067    -    0
  8 Seek_Time_Performance   P-S--K   112   092   040    -    35
  9 Power_On_Hours          -O--CK   002   002   000    -    43082
 10 Spin_Retry_Count        PO--CK   100   100   060    -    0
 12 Power_Cycle_Count       -O--CK   100   100   000    -    424
183 Runtime_Bad_Block       -O--CK   100   100   000    -    0
184 End-to-End_Error        PO--CK   100   100   097    -    0
187 Reported_Uncorrect      -O--CK   100   038   000    -    18953691004992
188 Command_Timeout         -O--CK   100   100   000    -    5636097
190 Airflow_Temperature_Cel -O---K   075   056   045    -    25 (Min/Max 20/29)
191 G-Sense_Error_Rate      -O--CK   091   091   000    -    2457
192 Power-Off_Retract_Count -O--CK   100   100   000    -    1310740
193 Load_Cycle_Count        -O--CK   064   064   000    -    360423
196 Reallocated_Event_Count -O--CK   100   100   000    -    49
197 Current_Pending_Sector  -O--CK   034   017   000    -    1720
198 Offline_Uncorrectable   ----CK   100   100   000    -    0
199 UDMA_CRC_Error_Count    -OS-CK   100   100   000    -    0
223 Load_Retry_Count        -O-R-K   100   100   000    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      1  Comprehensive SMART error log
0x03       GPL     R/O      1  Ext. Comprehensive SMART error log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x09           SL  R/W      1  Selective self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer

SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
Device Error Count: 64 (device log contains only the most recent 4 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 64 [3] occurred at disk power-on lifetime: 40254 hours (1677 days + 6 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 06 00 00 00 1e 78 00 00 00  Error: UNC 6 sectors at LBA = 0x001e7800 = 1996800

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 06 00 00 00 1e 78 00 40 00     00:00:36.977  READ DMA EXT
  25 00 00 00 40 00 00 00 1e 78 00 40 00     00:00:33.230  READ DMA EXT
  25 00 00 00 c0 00 00 74 6c 76 40 40 00     00:00:33.230  READ DMA EXT
  25 00 00 00 40 00 00 74 6c 76 00 40 00     00:00:33.229  READ DMA EXT
  25 00 00 01 00 00 00 74 6c 77 00 40 00     00:00:33.221  READ DMA EXT

Error 63 [2] occurred at disk power-on lifetime: 40254 hours (1677 days + 6 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 40 00 00 00 1e 78 00 00 00  Error: UNC 64 sectors at LBA = 0x001e7800 = 1996800

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 40 00 00 00 1e 78 00 40 00     00:00:33.230  READ DMA EXT
  25 00 00 00 c0 00 00 74 6c 76 40 40 00     00:00:33.230  READ DMA EXT
  25 00 00 00 40 00 00 74 6c 76 00 40 00     00:00:33.229  READ DMA EXT
  25 00 00 01 00 00 00 74 6c 77 00 40 00     00:00:33.221  READ DMA EXT
  25 00 00 00 c0 00 00 74 6c 74 40 40 00     00:00:33.219  READ DMA EXT

Error 62 [1] occurred at disk power-on lifetime: 40016 hours (1667 days + 8 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 41 00 08 00 00 00 1f eb 38 00 00  Error: UNC at LBA = 0x001feb38 = 2091832

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 30 00 00 00 3f eb 90 40 08  3d+22:11:28.579  READ FPDMA QUEUED
  60 00 08 00 28 00 00 00 3f eb 88 40 08  3d+22:11:28.578  READ FPDMA QUEUED
  60 00 08 00 b0 00 00 00 1f eb 38 40 08  3d+22:11:28.561  READ FPDMA QUEUED
  60 00 08 00 a8 00 00 00 3f eb 80 40 08  3d+22:11:28.561  READ FPDMA QUEUED
  ef 00 10 00 03 00 00 00 00 00 00 a0 08  3d+22:11:28.561  SET FEATURES [Enable SATA feature]

Error 61 [0] occurred at disk power-on lifetime: 40016 hours (1667 days + 8 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 41 00 08 00 00 00 1f eb 30 00 00  Error: UNC at LBA = 0x001feb30 = 2091824

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 00 08 00 20 00 00 00 3f eb 80 40 08  3d+22:11:24.703  READ FPDMA QUEUED
  60 00 08 00 60 00 00 00 1f eb 30 40 08  3d+22:11:22.805  READ FPDMA QUEUED
  60 00 08 00 58 00 00 00 1f eb f8 40 08  3d+22:11:22.805  READ FPDMA QUEUED
  ef 00 10 00 03 00 00 00 00 00 00 a0 08  3d+22:11:22.805  SET FEATURES [Enable SATA feature]
  ef 00 10 00 02 00 00 00 00 00 00 a0 08  3d+22:11:22.794  SET FEATURES [Enable SATA feature]

SMART Extended Self-test Log Version: 1 (1 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed: read failure       90%     42965         1948272
# 2  Short offline       Completed: read failure       90%     42964         1948272
# 3  Extended offline    Completed: read failure       90%     40016         1957312
# 4  Short offline       Completed: read failure       90%     40016         1957312
# 5  Extended offline    Completed without error       00%     29476         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Status Version:                  3
SCT Version (vendor specific):       256 (0x0100)
Device State:                        Active (0)
Current Temperature:                    25 Celsius
Power Cycle Min/Max Temperature:     20/29 Celsius
Lifetime    Min/Max Temperature:     13/44 Celsius
Specified Max Operating Temperature:    24 Celsius
Under/Over Temperature Limit Count:   0/0

SCT Temperature History Version:     2
Temperature Sampling Period:         1 minute
Temperature Logging Interval:        1 minute
Min/Max recommended Temperature:      0/60 Celsius
Min/Max Temperature Limit:           -40/65 Celsius
Temperature History Size (Index):    128 (106)

Index    Estimated Time   Temperature Celsius
 107    2026-07-08 08:42    25  ******
 ...    ..(  6 skipped).    ..  ******
 114    2026-07-08 08:49    25  ******
 115    2026-07-08 08:50    24  *****
 116    2026-07-08 08:51    25  ******
 ...    ..(  9 skipped).    ..  ******
 126    2026-07-08 09:01    25  ******
 127    2026-07-08 09:02    24  *****
   0    2026-07-08 09:03    25  ******
   1    2026-07-08 09:04    24  *****
   2    2026-07-08 09:05    25  ******
 ...    ..(  2 skipped).    ..  ******
   5    2026-07-08 09:08    25  ******
   6    2026-07-08 09:09    24  *****
   7    2026-07-08 09:10    24  *****
   8    2026-07-08 09:11    25  ******
   9    2026-07-08 09:12    24  *****
  10    2026-07-08 09:13    25  ******
 ...    ..(  4 skipped).    ..  ******
  15    2026-07-08 09:18    25  ******
  16    2026-07-08 09:19    24  *****
  17    2026-07-08 09:20    25  ******
 ...    ..( 16 skipped).    ..  ******
  34    2026-07-08 09:37    25  ******
  35    2026-07-08 09:38    24  *****
  36    2026-07-08 09:39    25  ******
  37    2026-07-08 09:40    25  ******
  38    2026-07-08 09:41    24  *****
  39    2026-07-08 09:42    25  ******
 ...    ..(  8 skipped).    ..  ******
  48    2026-07-08 09:51    25  ******
  49    2026-07-08 09:52    24  *****
  50    2026-07-08 09:53    25  ******
 ...    ..(  6 skipped).    ..  ******
  57    2026-07-08 10:00    25  ******
  58    2026-07-08 10:01    24  *****
  59    2026-07-08 10:02    25  ******
 ...    ..(  3 skipped).    ..  ******
  63    2026-07-08 10:06    25  ******
  64    2026-07-08 10:07    24  *****
  65    2026-07-08 10:08    25  ******
  66    2026-07-08 10:09    25  ******
  67    2026-07-08 10:10    25  ******
  68    2026-07-08 10:11    24  *****
  69    2026-07-08 10:12    25  ******
 ...    ..(  5 skipped).    ..  ******
  75    2026-07-08 10:18    25  ******
  76    2026-07-08 10:19    24  *****
  77    2026-07-08 10:20    25  ******
 ...    ..( 28 skipped).    ..  ******
 106    2026-07-08 10:49    25  ******

SCT Error Recovery Control:
           Read:     85 (8.5 seconds)
          Write:     85 (8.5 seconds)

Device Statistics (GP/SMART Log 0x04) not supported

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  2            0  Command failed due to ICRC error
0x0002  2            0  R_ERR response for data FIS
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0005  2            0  R_ERR response for non-data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
0x0009  2        26207  Transition from drive PhyRdy to drive PhyNRdy
0x000a  2            1  Device-to-host register FISes sent due to a COMRESET
0x000b  2            0  CRC errors within host-to-device FIS
0x000d  2            0  Non-CRC errors within host-to-device FIS

