Upgraded to version 22.43.1014

]]> Upgraded to version 22.43.1014

]]>

Updated Supported Environments

]]>

Updated driver

Updated supported platforms

]]> Important Notes:

Ver. 1.0.0.22(F) contains updates to the firmware packaging and is functionally equivalent to ver. 1.0.0.22. It is not necessary to upgrade with Revision F if a previous component revision was used to upgrade the firmware to version 1.0.0.22.

This Linux component is compatible with Service Pack for ProLiant 2024.11.00.00.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where Innovation Engine (IE) may improperly reset every 24 hours.

Known Issues:

None

]]> Important Notes:

This Linux component is compatible with Service Pack for ProLiant 2024.11.00.00.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where Innovation Engine (IE) may improperly reset every 24 hours.

Known Issues:

None

]]> Support SHA384

]]>

Added support for Azure Stack HCI 23H2.

]]>

Fix the controller library compatible issue.

]]>

Added support for ESXi 9.0

]]>

Fixes the displayed message of direct attached NVMe firmware flashing to align FW activation result by OS.

]]>

Fix the controller library compatible issue.

]]> This product fixes the wording of "Ndis Poll Mode" and "Encapsulation Overhead," including both English and other translations.

]]> This product enhanced the compatibility with firmware of Fortville 9.5.

]]> NMST version 4.31.0.150

This version is supported on VMware ESXi 8.0 Update 3 only.

]]> Added Support for RHEL 10

]]>

Fixed flashing issue through SDR method

]]>

Updated supported environments

]]>

Updated supported environments

]]>

fix for genericmsi version

]]>

Added Write Cache Status field to the info page for physical drives when "pd all show detail" is used.

]]>

Corrected wrong wording of Parity Initialization messages.

Fixed vulnerability CVE-2023-45853.

]]>

Added support for RHEL 10.

]]>

Fixed flashing issue through SDR method

]]>

This product fixes an issue where the speed may be downgraded to Gen3.

This product fixes an issue where the Linux driver fails to load due to an EEPROM checksum error when the RDE:MACAddress property is patched.

This product fixes an issue where the NIC is not detected after performing the RDE patch operation on NetworkDeviceFunctions settings.

This product fixes an issue where the RDE: Setting property (AutoSpeedNegotiationEnabled) does not cause the property value to update, returning a code 400.

This product fixes an issue where the RDE fails to perform the get operation when the adapter is configured as pass-through.

This product fixes an issue where the RDE property (FlowControlStatus) does not report the correct status after the RDE property FlowControlConfiguration is set to Tx.

This product fixes an issue where the RDE patch operation fails on the AutoSpeedNegotiationEnabled property.

]]> Add new support platform.

]]>

Added support for ESXi 9.0

]]>

Fix the controller library compatible issue.

]]>

Added support for RHEL10.

]]>

Fixed flashing issue through SDR method

]]> TBD

]]>

This product now supports SUSE Linux Enterprise Server 15 SP6.

]]> Fix 1) PCIe link length drop in AMD x2 system configuration
2) Drive detection after hot re-insert on Windows
3) Other regular FW patch release.

]]> Added support for:

Red Hat Enterprise Linux 10.0

Updated to version 14.4.473.24

]]> 7.30 Drop

]]>

Initial release.

]]>

Added support for Azure Stack HCI 23H2.

]]>

Fix contains code improvements for SMART reporting.

]]>

Added support for Azure Stack HCI 23H2.

]]>

Fix the controller library compatible issue.

]]> The following enhancement has been added in this version:

Added support of RHEL 8.7
Added support of RHEL 9.1
Added support of SLES15 SP4

]]> The following fixes were incorporated in this version:

The Enabled-ClusterS2D command now completes successfully when executed on a SATA drive within a D3610 disk enclosure for a NonStop solution.
The smart carrier, which is the drive case for SAS drives, now authenticates in the D3610/D3710 drive enclosure.
Added new 7-segment error codes E0 and E1 to report issues with Fan modules A and B, respectively. These new codes only apply to the D3610/D3710 and only display when running firmware 5.04.
If the storage enclosure processor within the I/O module fails, a hard reset (power down and then power up) is executed to ensure the processor comes back online.

Please refer to the Release Notes for the complete listing of fixes, enhancements, known issues and work-arounds corresponding to this firmware.

]]> The following enhancement has been added in this version:

Added support of Rhel 7.8
Added support of Rhel 8.2
Added support of SLES15 SP2

]]> The following fixes were incorporated in this version:

The Enabled-ClusterS2D command now completes successfully when executed on a SATA drive within a D3610 disk enclosure for a NonStop solution.
The smart carrier, which is the drive case for SAS drives, now authenticates in the D3610/D3710 drive enclosure.
Added new 7-segment error codes E0 and E1 to report issues with Fan modules A and B, respectively. These new codes only apply to the D3610/D3710 and only display when running firmware 5.04.
If the storage enclosure processor within the I/O module fails, a hard reset (power down and then power up) is executed to ensure the processor comes back online.

Please refer to the Release Notes for the complete listing of fixes, enhancements, known issues and work-arounds corresponding to this firmware.

]]> TBD

]]> This product enhances libfwupg to improve NVRAM configuration updates.

]]>

Added support for RHEL 10.

]]>

This maintenance revision improves data integrity.

The risk of not upgrading to this firmware is the increased possibility of data corruption in certain error and timing conditions.

]]> Updated multi-language translation.

]]> Important Notes:

This version of the System ROM contains updates aligned with the Intel Tatlow IPU 2025.2 update. This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.00.03.700 (2.30_01_07_2025).

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system may encounter RSOD and fail to update firmware while performing firmware update.

Addressed an issue where the Name field of the Logical Drive under MR controller page might be missing or changed unintentionally after exiting and going back to the MR controller page.

Known Issues:

None]]> Important Notes:

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.00.03.700 (2.30_01_07_2025).

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system might RSOD when performing firmware update via Firmware Management Protocol.

Known Issues:

None]]>

Changes and improvements made in 7500 firmware HPK1 over previous firmware HPK0 are to enhance receiver signals by changing the drive’s internal PHY register values on Gen11 x2 direct attached system.

]]>

Added support for RHEL10.

]]>

Fix contains code improvements for SMART reporting.

]]> TBD

]]> This product updated the copyright information and compatibility with firmware

]]> TBD

]]>

This product enhances to enable RSS code to support systems with more than 256 CPU cores.

This product enhances to support Wake-on-LAN with 1G connection.

]]> Updated multi-language translation.

Removed Expired SUSE and Vmware Certificates.

]]> Important Notes:

This version of the System ROM contains updates aligned with the Intel Mehlow IPU 2025.2 update. This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 05.01.05.005.

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the Name field of the Logical Drive under MR controller page might be missing or changed unintentionally after exiting and going back to the MR controller page.

Known Issues:

None]]> Added pop-up message for all Intelligent Provisioning boot paths to warn users of the risk of data loss.

]]> Important Notes:

This version of the System ROM contains updates aligned with the Intel Product Update (IPU) version IPU.2025.1 guidance. This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 05.01.05.005.

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system iLO remote console might hang when the System Utilities Language is set to Japanese.

Known Issues:

None

]]> TBD

]]> This product now supports Red Hat Enterprise Linux 9 update 4.

]]> MFT prerequisite RPMs for Mellanox adapter firmware update in Secure Boot mode.

]]> Important Notes:

This version of the Server Platform Services (SPS) Firmware contains updates aligned with the Intel Product Update (IPU) version IPU 2025.1 guidance. This version of the SPS 05.01.05.005 should be paired with System ROM 3.50 (01/16/2025) or later.

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Enhancements/New Features:

This version is in compliance with IPU 2025.1 guidance.

Known Issues:

None]]> Important Notes:

This version of the Server Platform Services (SPS) Firmware contains updates aligned with the Intel Product Update (IPU) version IPU.2023.3 guidance.

Firmware Dependencies:

None

Enhancements/New Features:

This version is in compliance with Intel IPU.2023.3 guidance.

Known Issues:

None]]>

Added support for ESXi 9.0

]]>

Fix the controller library compatible issue.

]]>

This is a planned maintenance release covering bug fixes. This firmware includes updates to improve PLI circuit reliability.

]]>

HPG3 is a planned maintenance release covering bug fixes for 2.5” and M.2. There are no critical functional updates, and risk is low for customers who do not upgrade, especially if drives are not stored without power for a long period of time (~2 years).

]]>

Added support for Azure Stack HCI 23H2

]]>

Fixes the displayed message of direct attached NVMe firmware flashing to align FW activation result by OS.

]]>

Added support for Microsoft Windows Server 2025.

]]>

Fix the controller library compatible issue.

]]> Important Notes:

This version of the Server Platform Services (SPS) Firmware contains updates aligned with the Intel Product Update (IPU) version IPU 2025.1 guidance. This version of the SPS 06.00.03.700 (2.30_01_07_2025) should be paired with System ROM 2.30 (01/16/2025) or later.

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Enhancements/New Features:

This version is in compliance with IPU 2025.1 guidance.

Known Issues:

None]]> Important Notes:

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Enhancements/New Features:

This version is in compliance with IPU 2025.1 guidance.

Known Issues:

None]]> Updated to version 9.4.11.20

]]> Updated to version 9.4.10.20

]]>

Added support for ESXi 9.0

]]>

Fixes the logic bug in the media cache cleaning abort handling that caused the drive to choose and execute the R/W command before the Request Sense to prevent assert.

Adding other logging and FW enhancements.

]]>

This product fixes an issue where the speed may be downgraded to Gen3.

This product fixes an issue where the Linux driver fails to load due to an EEPROM checksum error when the RDE:MACAddress property is patched.

This product fixes an issue where the NIC is not detected after performing the RDE patch operation on NetworkDeviceFunctions settings.

This product fixes an issue where the RDE: Setting property (AutoSpeedNegotiationEnabled) does not cause the property value to update, returning a code 400.

This product fixes an issue where the RDE fails to perform the get operation when the adapter is configured as pass-through.

This product fixes an issue where the RDE property (FlowControlStatus) does not report the correct status after the RDE property FlowControlConfiguration is set to Tx.

This product fixes an issue where the RDE patch operation fails on the AutoSpeedNegotiationEnabled property.

]]> Add new support platform.

]]>

Added support for Azure Stack HCI 23H2.

]]>

Fix the controller library compatible issue.

]]> TBD

]]> This product updated the copyright information and compatibility with firmware

]]> This product fix an issue that TCP traffic on VMs might be interrupted if PF undergoes a reset.

]]> This product fixes an issue where Large Send Offload (LSO) is not working.

]]> This product enhanced the compatibility with firmware of Fortville 9.5 and Columbiaville 4.5.

]]> Firmware for the following devices has been updated to 20.43.2026:

HPE InfiniBand HDR/Ethernet 200Gb 1-port QSFP56 PCIe3 x16 MCX653105A-HDAT Adapter - P06154-B21
HPE InfiniBand HDR100/Ethernet 100Gb 1-port QSFP56 PCIe3 x16 MCX653105A-ECAT Adapter - P06250-B21
HPE InfiniBand HDR100/Ethernet 100Gb 2-port QSFP56 PCIe3 x16 MCX653106A-ECAT Adapter - P06251-B21

Security Hardening Enhancements: This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your device's firmware to this release to improve the firmware security and reliability of your device.

No changes or new features have been included in version 20.43.2026.

]]> The following issues have been fixed in version 20.43.2026:

A linkup issue vs a 3rd party switch (BCM53405).
A reference counter issue that resulted in the firmware assertion 0x889f with CQ reference counter underflow to solve a race condition.

]]> Firmware for the following devices has been updated to 20.43.1014:

HPE InfiniBand HDR/Ethernet 200Gb 1-port QSFP56 PCIe3 x16 MCX653105A-HDAT Adapter - P06154-B21
HPE InfiniBand HDR100/Ethernet 100Gb 1-port QSFP56 PCIe3 x16 MCX653105A-ECAT Adapter - P06250-B21
HPE InfiniBand HDR100/Ethernet 100Gb 2-port QSFP56 PCIe3 x16 MCX653106A-ECAT Adapter - P06251-B21

New features and changes included in version 20.43.1014:

Added the option to indicate an error CQE event on every selected function per eSwitch manager. This indication is defined as a new WQE including the relevant information about the error (such as: syndrome, function_id, timestamp, QPs num etc.).
Extended kernel lockdown permission set. The following sub-operations can now be called by tools (permission TOOLS_RESORCES) using new HCA capability bitmask field: tool_partial_cap.

The 5 sub-operations are:

QUERY_HCA_CAP with other function
QUERY_VUID with direct data
QUERY_ROCE_ADDRESS with other vport
SET_HCA_CAP with other function
POSTPONE_CONNECTED_QP_TIMEOUT with other vport

The new added caps are:

tool_partial_cap.postpone_conn_qp_timeout_other_vport,
tool_partial_cap.set_hca_cap_other_func
tool_partial_cap.query_roce_addr_other_vport
tool_partial_cap.query_vuid_direct_data
tool_partial_cap.query_hca_cap_other_func

]]> The following issues have been fixed in version 20.43.1014:

Setup crash when "create_sq" used invalid mbox.
The firmware always returned the "next" value to be applied when querying FACTORY default NV configuration values.

]]>

Added support for Azure Stack HCI 23H2

]]>

Fixes the displayed message of direct attached NVMe firmware flashing to align FW activation result by OS.

]]>

Added support for Microsoft Windows Server 2025.

]]>

Maintenance firmware release to introduce fixes from previous firmware.

Fix the controller library compatible issue.

]]> Important Notes:

This version of the System ROM contains updates aligned with the Intel IPU 2025.2 updates.

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.04.04.702 (2.30_01_06_2025).

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system Intel PCH model name is unknown in RBSU System information.

Addressed an issue where the system might log into the wrong DIMM index in the Server Configuration Lock detection log after removing the system DIMM.

Addressed an issue where the system iLORest might time out.

Addressed an issue where the system might RSOD when performing firmware update via Firmware Management Protocol.

Known Issues:

None

]]> Important Notes:

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.04.04.702 (2.30_01_06_2025).

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system Intel PCH model name is unknown in RBSU System information.

Addressed an issue where the system might log into the wrong DIMM index in the Server Configuration Lock detection log after removing the system DIMM.

Addressed an issue where the system iLORest might time out.

Addressed an issue where the system might RSOD when performing firmware update via Firmware Management Protocol.

Known Issues:

None]]> Important Notes:

This version of the Server Platform Services (SPS) Firmware contains updates aligned with the Intel Product Update (IPU) version IPU 2025.1 guidance. This version of the SPS 04.01.05.105 should be paired with System ROM 3.40 (01/16/2025) or later.

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Enhancements/New Features:

This version is in compliance with IPU 2025.1 guidance.

Known Issues:

None]]> Important Notes:

This version of the Server Platform Services (SPS) Firmware contains updates aligned with the Intel Product Update (IPU) version IPU.2023.3 guidance.

Firmware Dependencies:

None

Enhancements/New Features:

This version is in compliance with IPU.2023.3 guidance.

Known Issues:

None

]]>

Added support for RHEL10.

]]>

Fixed flashing issue through SDR method

]]> The following fixes were incorporated in this version:

Code optimization to save memory repo.
TLB exception seen while doing esp reset when expander reset was in progress.
Added the psoc 8.93 binary in peripheral images, updated the reveille version numbers.
Added whole new Delta PS-pmbus code , Updated the ESP version number.

Please refer to the Release Notes for the complete listing of fixes, enhancements, known issues and work-arounds corresponding to this firmware.

]]> TBD

]]> This product added support to new Gen11 servers.

]]>

Fixes the displayed message of direct attached NVMe firmware flashing to align FW activation result by OS.

]]>

Maintenance firmware release to introduce fixes from previous firmware.

Fix the controller library compatible issue.

]]> TBD

]]>

This product enhanced to support log FW Failure Critical Data in Recovery Mode.

This product enhanced to support add module parameters pause_rx and pause_tx for Link Flow Control and enable it by default.

]]> Firmware for the following devices has been updated to 14.32.1900:

817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)
817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)

Firmware for the following device has been updated to 16.35.4030:

874253-B21 (HPE Ethernet 100Gb 1-port 842QSFP28 Adapter)

Security Hardening Enhancements
This release contains important reliability improvements and security hardening enhancements. NVIDIA recommends upgrading your devices firmware to this release to improve the devices’ firmware security and reliability.

No new features or changes have been included in firmware version 14.32.1900.

New features and changes included in firmware version 16.35.4030:

Added support for postponing QP timeout "retry exceeded" errors for traffic directed at specific destinations. This new capability prevents broken connections for destinations in downtime because of live migration.

]]> No fixes have been included in firmware version 14.32.1900.

The following issues have been fixed in firmware version 16.35.4030:

VF FLR would get stuck when its PF triggered the FLR as well.
Unexpected source UDP port appeared in RoCE packets when the firmware ignored a non-PF driver configuration for RoCE source UDP port control (as set in SET_HCA_CAP.sw_r_roce_src_udp_port).

]]> Firmware for the following devices has been updated to 14.32.1010:

817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)
817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)

Firmware for the following device has been updated to 16.35.3502:

874253-B21 (HPE Ethernet 100Gb 1-port 842QSFP28 Adapter)

New features and changes included in firmware version 14.32.1010:

Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its rate limit.
Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
Limited the external loopback speed to the used module's capabilities.
Improved linkup time when using the fast linkup capability.
Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.

New features and changes included in firmware version 16.35.3502:

Modified the TCP IPv4 flows so that the steering TIR rx_hash_symmetric field is now valid only when both the SRC and DST fields are not set to zero.

]]> The following issues have been fixed in firmware version 14.32.1010:

Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
The system could not create more than 128K QPs.
On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
Packet Pacing rate was used if asymmetric VFs was enabled.
Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.

No fixes are included in firmware version 16.35.3502.

]]> Removed Expired SUSE and Vmware Certificates.

Improved detection and interaction with certain PCIe cards during UEFI HBA discovery process.

]]> Important Notes:

This version of the System ROM contains updates aligned with the Intel IPU 2025.2 updates.

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.01.05.105.

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system might have false IML message "Processor X, DIMM Y - This NVDIMM is NOT a HPE SmartMemory NVDIMM".

Addressed an issue where the system might trigger BitLocker Recovery after reboot.

Known Issues:

None

]]> Removed Expired SUSE and Vmware Certificates.

Improved detection and interaction with certain PCIe cards during UEFI HBA discovery process.

]]> Important Notes:

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.01.05.105.

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system might have false IML message "Processor X, DIMM Y - This NVDIMM is NOT a HPE SmartMemory NVDIMM".

Addressed an issue where the system might trigger BitLocker Recovery after reboot.

Known Issues:

None]]> TBD

]]>

This product enhances to add support for Tunnel based TPA (TCP Packet Aggregation).

This product enhances the coredump feature for generating the summary of a coredump file.

]]>

Added support for Azure Stack HCI 23H2.

]]>

Added support for Microsoft Windows Server 2025

]]>

Fix the controller library compatible issue.

]]>

Added support for RHEL 10.

]]>

Fixed flashing issue through SDR method

]]>

Added support for ESXi 9.0

]]>

Fix the controller library compatible issue.

]]>

Added support for RHEL 10.

]]>

This maintenance revision improves data integrity. The risk of not upgrading to this firmware is the increased possibility of data corruption in certain error and timing conditions.

]]> Firmware for the following devices has been updated to 12.28.2302:

825110-B21 (HPE InfiniBand EDR/Ethernet 100Gb 1-port 840QSFP28 Adapter)
825111-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 840QSFP28 Adapter)

Firmware for the following devices has been updated to 16.35.4506:

879482-B21 (HPE InfiniBand FDR/Ethernet 40/50Gb 2-port 547FLR-QSFP Adapter)
872726-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 841QSFP28 Adapter)

Important : Security Hardening Enhancements - This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your device firmware to this version to improve the firmware security and reliability of your device.

No new Features and changes included in version 12.28.2302.

New features and changes included in version 16.35.4506:

Added address validation in MLNX OEM CMD 0x0032 (get debug info) to be 4- bytes aligned.

]]> No new fixes have been added in version 12.28.2302.

The following issues have been fixed in version 16.35.4506:

Incorrect MPLS packets discards flow occurred when the GLOBAL pause capability was disabled.

]]> Firmware for the following devices has been updated to 12.28.2302:

825110-B21 (HPE InfiniBand EDR/Ethernet 100Gb 1-port 840QSFP28 Adapter)
825111-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 840QSFP28 Adapter)

Firmware for the following devices has been updated to 16.35.4030:

879482-B21 (HPE InfiniBand FDR/Ethernet 40/50Gb 2-port 547FLR-QSFP Adapter)
872726-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 841QSFP28 Adapter)

No new Features and changes included in version 12.28.2302.

New features and changes included in version 16.35.4030:

Added support for postponing QP timeout "retry exceeded" errors for traffic directed at specific destinations. This new capability prevents broken connections for destinations in downtime because of live migration.

]]> No new fixes have been added in version 12.28.2302.

The following issues have been fixed in version 16.35.4030:

VF FLR would get stuck when its PF triggered the FLR as well.
Unexpected source UDP port appeared in RoCE packets when the firmware ignored a non-PF driver configuration for RoCE source UDP port control (as set in SET_HCA_CAP.sw_r_roce_src_udp_port).

]]> 1.Fixes the logic bug in the media cache cleaning abort handling that caused the drive to choose and execute the R/W command before the Request Sense to prevent assert.
2. Adding other logging and FW enhancements.

]]> Optimize thermal maximum continuous operation temperature values.

]]>

Added support for RHEL 10.

]]>

Fixed flashing issue through SDR method

]]>

Added support for RHEL 10.

]]>

Fixed flashing issue through SDR method

]]>

Added support for Azure Stack HCI 23H2.

]]>

Added support for Microsoft Windows Server 2025.

]]>

Fix the controller library compatible issue.

]]> Updated multi-language translation.

]]> Important Notes:

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system may encounter RSOD and fail to update firmware while performing firmware update.

Addressed an issue where the Name field of the Logical Drive under MR controller page might be missing or changed unintentionally after exiting and going back to the MR controller page.

Known Issues:

None]]> Important Notes:

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.00.03.700 (2.30_01_07_2025).

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system might RSOD when performing firmware update via Firmware Management Protocol.

Known Issues:

None]]> This product fixes the wording of "Ndis Poll Mode" and "Encapsulation Overhead," including both English and other translations.

]]> This product now supports Azure Stack HCI OS.

]]>

Added fix to address a rare case where drive health queries can trigger false drive predictive failure.

For more information, refer to HPE Customer Advisory at the following URL: https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-a00146367en_us which will be active on 19-Mar-2025.

]]>

Remove ROM flash way from this FWPKG.

]]> Important Notes:

Ver. 0.2.3.0(D) contains updates to the firmware packaging and is functionally equivalent to ver. 0.2.3.0. It is not necessary to upgrade with Revision D if a previous component revision was used to upgrade the firmware to version 0.2.3.0.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where Innovation Engine (IE) may improperly reset every 24 hours. On some systems this could result in a brief drop in CPU utilization or network traffic lasting less than a second.

Known Issues:

None

]]> Important Notes:

Ver. 0.2.3.0(B) contains updates to the firmware packaging and is functionally equivalent to ver. 0.2.3.0. It is not necessary to upgrade with Revision B if a previous component revision was used to upgrade the firmware to version 0.2.3.0.

Firmware Dependencies:

None

Problems Fixed:

Known Issues:

None

]]>

Added support for RHEL 10.

]]>

Fixed flashing issue through SDR method

]]> Important : Security Hardening Enhancements - This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your device firmware to this version to improve the firmware security and reliability of your device.

New features and changes included in version 16.35.4030:

Added support for postponing QP timeout "retry exceeded" errors for traffic directed at specific destinations. This new capability prevents broken connections for destinations in downtime because of live migration.

]]> The following issues have been fixed in version 16.35.4030:

VF FLR would get stuck when its PF triggered the FLR as well.
Unexpected source UDP port appeared in RoCE packets when the firmware ignored a non-PF driver configuration for RoCE source UDP port control (as set in SET_HCA_CAP.sw_r_roce_src_udp_port).

New features and changes included in version 16.35.4030:

Added support for postponing QP timeout "retry exceeded" errors for traffic directed at specific destinations. This new capability prevents broken connections for destinations in downtime because of live migration.

]]> The following issues have been fixed in version 16.35.4030:

VF FLR would get stuck when its PF triggered the FLR as well.
Unexpected source UDP port appeared in RoCE packets when the firmware ignored a non-PF driver configuration for RoCE source UDP port control (as set in SET_HCA_CAP.sw_r_roce_src_udp_port).

]]> Updated multi-language translation.

]]> Important Notes:

This revision of the System ROM includes AMD reference code MilanPI 1.0.0.F for AMD 3rd Generation EPYC processors. This revision of the System ROM includes AMD reference code RomePI 1.0.0.M for AMD 2nd Generation EPYC processors.

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where system may hang at POST when there are 8TB system memory and E810 NIC card installed.

Addressed an issue where the Name field of the Logical Drive under MR controller page might be missing or changed unintentionally after exiting and going back to the MR controller page.

Known Issues:

None]]> Important Notes:

This revision of the System ROM includes AMD reference code MilanPI 1.0.0.G for AMD 3rd Generation EPYC processors. This revision of the System ROM includes AMD reference code RomePI 1.0.0.M for AMD 2nd Generation EPYC processors.

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system may encounter RSOD and fail to update firmware while performing firmware update.

Known Issues:

None]]> Updated the kit to version 6.0.0.1-4

]]> Updated the kit to version 6.0.0.1-4

]]>

Added support for RHEL 10.

]]>

Fixed flashing issue through SDR method

]]> Firmware for the following devices has been updated to 14.32.1900:

P21930-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4121A-XCAT Adapter)
P11341-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4621A-ACAB OCP3 Adapter)

Firmware for the following device has been updated to 16.35.4030:

P21927-B21 (HPE Ethernet 100Gb 2-Port QSFP28 MCX516A-CCHT Adapter)

No new features or changes have been included in firmware version 14.32.1900.

New features and changes included in firmware version 16.35.4030:

Added support for postponing QP timeout "retry exceeded" errors for traffic directed at specific destinations. This new capability prevents broken connections for destinations in downtime because of live migration.

]]> No fixes have been included in firmware version 14.32.1900.

The following issues have been fixed in firmware version 16.35.4030:

VF FLR would get stuck when its PF triggered the FLR as well.
Unexpected source UDP port appeared in RoCE packets when the firmware ignored a non-PF driver configuration for RoCE source UDP port control (as set in SET_HCA_CAP.sw_r_roce_src_udp_port).

]]> This product fixes an issue where Large Send Offload (LSO) is not working.

]]> This product now supports Azure Stack HCI OS.

]]> Important Notes:

None

Firmware Dependencies:

For HPE ProLiant Gen10 Plus servers, iLO5 version 2.55 or above is required to upgrade to this version.

Enhancements/New Features:

Changed certain behaviors to avoid machine power failures when significant power consumption devices are introduced.

Problems Fixed:

None

Known Issues:

None

]]> Important Notes:

None

Firmware Dependencies:

For HPE ProLiant Gen10 Plus servers, iLO5 version 2.55 or above is required to upgrade to this version.

Enhancements/New Features:

Changed certain behaviors to avoid machine power failures when significant power consumption devices are introduced.

Problems Fixed:

None

Known Issues:

None

]]>

Added support for ESXi 9.0

]]>

Fix the controller library compatible issue.

]]>

fix for genericmsi version

]]>

Added Write Cache Status field to the info page for physical drives.

]]>

Fixed inappropriately prompted Rapid Parity Initialization messages.

Fixed vulnerability CVE-2023-45853.

]]> Removed Expired SUSE and Vmware Certificates.

Improved detection and interaction with certain PCIe cards during UEFI HBA discovery process.

]]> Important Notes:

This version of the System ROM contains updates aligned with the Intel IPU 2025.2 updates.

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.01.05.105.

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system might have false IML message "Processor X, DIMM Y - This NVDIMM is NOT a HPE SmartMemory NVDIMM".

Addressed an issue where the system might trigger BitLocker Recovery after reboot.

Known Issues:

None

]]> Removed Expired SUSE and Vmware Certificates.

Improved detection and interaction with certain PCIe cards during UEFI HBA discovery process.

]]> Important Notes:

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.01.05.105.

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system might have false IML message "Processor X, DIMM Y - This NVDIMM is NOT a HPE SmartMemory NVDIMM".

Addressed an issue where the system might trigger BitLocker Recovery after reboot.

Known Issues:

None]]> This product fixes the wording of "Ndis Poll Mode" and "Encapsulation Overhead," including both English and other translations.

]]> This product now supports Azure Stack HCI OS.

]]> This Firmware package contains following firmware versions:

Adapter	Speed	Universal Boot Image	Firmware	UEFI	Boot Bios
HPE SN1200E 16Gb Dual Port Fibre Channel Host Bus Adapter	16Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1200E 16Gb Single Port Fibre Channel Host Bus Adapter	16Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1600E 32Gb Dual Port Fibre Channel Host Bus Adapter	32Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1600E 32Gb Single Port Fibre Channel Host Bus Adapter	32Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1610E 32Gb Single Port Fibre Channel Host Bus Adapter	32Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1610E 32Gb Dual Port Fibre Channel Host Bus Adapter	32Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1700E 64Gb Single Port Fibre Channel Host Bus Adapter	64Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1700E 64Gb Dual Port Fibre Channel Host Bus Adapter	64Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0

]]> This Firmware package contains following firmware versions:

Adapter	Speed	Universal Boot Image	Firmware	UEFI	Boot Bios
HPE SN1200E 16Gb Dual Port Fibre Channel Host Bus Adapter	16Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1200E 16Gb Single Port Fibre Channel Host Bus Adapter	16Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1600E 32Gb Dual Port Fibre Channel Host Bus Adapter	32Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1600E 32Gb Single Port Fibre Channel Host Bus Adapter	32Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1610E 32Gb Single Port Fibre Channel Host Bus Adapter	32Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1610E 32Gb Dual Port Fibre Channel Host Bus Adapter	32Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1700E 64Gb Single Port Fibre Channel Host Bus Adapter	64Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1700E 64Gb Dual Port Fibre Channel Host Bus Adapter	64Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0

]]> Driver version 5.4.82.1

]]>

Added support for RHEL 10.

]]>

Fixes the displayed message of direct attached NVMe firmware flashing to align FW activation result by OS.

]]> Updated to version 1.0.0.1

]]>

Added support for RHEL 10.

]]>

Fixed flashing issue through SDR method

]]>

Update build environment with Rhel9 SHA384

Update OS

]]>

Update build environment with SHA384

Update OS

]]>

Added support for Azure Stack HCI 23H2.

]]>

Fix the controller library compatible issue.

]]>

Added support for RHEL 10.

]]>

Fixes the logic bug in the media cache cleaning abort handling that caused the drive to choose and execute the R/W command before the Request Sense to prevent assert.

Adding other logging and FW enhancements.

]]> Firmware for the following device has been updated to 14.32.1900:

P11338-B21 (HPE Ethernet 10Gb 2-port 548SFP+ Adapter)

No new features or changes have been included in firmware version 14.32.1900.

]]> No fixes have been included in firmware version 14.32.1900.

]]> Firmware for the following device has been updated to 14.32.1010:

P11338-B21 (HPE Ethernet 10Gb 2-port 548SFP+ Adapter)

New features and changes included in version 14.32.1010:

Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its rate limit.
Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
Limited the external loopback speed to the used module's capabilities.
Improved linkup time when using the fast linkup capability.
Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.

]]> The following issues have been fixed in component sub-version 1.0.6(C):

Transaction test error was reported while deploying the component using SPP from HPE Linux SDR.

The following changes have been made in component sub-version 1.0.6(B):

Product rebuilt to support FIPS mode enabled OS environment.

The following changes have been made in component sub-version 1.0.6(A):

Product rebuilt to have the new SHA 384 signature.

The following issues have been fixed in firmware version 14.32.1010:

Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
The system could not create more than 128K QPs.
On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
Packet Pacing rate was used if asymmetric VFs was enabled.
Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.

]]>

Added support for RHEL 10.

]]>

Fixed flashing issue through SDR method

]]>

Added support for ESXi 9.0

]]>

Fix the controller library compatible issue.

]]> Added Support For:

Red Hat Enterprise Linux 10

Red Hat Enterprise Linux 9.6

Updated Driver version 10.02.14.00-k1

]]> Updated Driver version 10.02.13.03-k1

]]> Support new Gen12 servers.

]]> Support both Gen10P and Gen11 servers

]]> Important Notes:

This version of the System ROM contains updates aligned with the Intel IPU 2025.2 updates.

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.04.04.702 (2.30_01_06_2025).

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system Intel PCH model name is unknown in RBSU System information.

Addressed an issue where the system might log into the wrong DIMM index in the Server Configuration Lock detection log after removing the system DIMM.

Addressed an issue where the system iLORest might time out.

Addressed an issue where the system might RSOD when performing firmware update via Firmware Management Protocol.

Addressed an issue where CPU power readings displayed in iLO were unbalanced between two processors.

Known Issues:

None

]]> Important Notes:

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.04.04.702 (2.30_01_06_2025).

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system Intel PCH model name is unknown in RBSU System information.

Addressed an issue where the system might log into the wrong DIMM index in the Server Configuration Lock detection log after removing the system DIMM.

Addressed an issue where the system iLORest might time out.

Addressed an issue where the system might RSOD when performing firmware update via Firmware Management Protocol.

Known Issues:

None]]> TBD

]]> This product corrects an issue which Windows Server 2022 crashes when system has high number of logical processors.

]]> TBD

]]> This product enhanced the compatibility with the new firmware.

]]>

Support new Gen12 servers.

]]>

Support Azure Stack HCI 23H2 OS.

Support new Gen12 servers.

]]> The following enhancement has been added in this version:

Added support of RHEL 8.7
Added support of RHEL 9.1
Added support of SLES15 SP4

]]> The following fixes were incorporated in this version:

Smart Array reporting "Storage Enclosure FW upgrade Problem Detected".
PSU version is showing as "No Ver" after inserted the New bel power PSU.
GEM_5_2 Coverity defect fix.

Please refer to the Release Notes for the complete listing of fixes, enhancements, known issues and work-arounds corresponding to this firmware.

]]> The following enhancement has been added in this version:

Added support of Rhel 7.8
Added support of Rhel 8.2
Added support of SLES15 SP2

]]> The following fixes were incorporated in this version:

Smart Array reporting "Storage Enclosure FW upgrade Problem Detected".
PSU version is showing as "No Ver" after inserted the New bel power PSU.
GEM_5_2 Coverity defect fix.

Please refer to the Release Notes for the complete listing of fixes, enhancements, known issues and work-arounds corresponding to this firmware.

]]>

Added support for RHEL10.

]]>

Fixes the potential drive hang issue after POH exceed 6.5 years. We suggest customers to update the FW as soon as possible to prevent inconvenience.

For more information, refer to HPE Customer Bulletin at the following URL: https://support.hpe.com/hpesc/public/docDisplay?docId=a00142174en_us

]]>

Added support for ESXi 9.0

]]>

Fixes the displayed message of direct attached NVMe firmware flashing to align FW activation result by OS.

]]>

Fix the controller library compatible issue.

]]>

Updated SBOM requirement

]]>

Added supported_platforms tag

]]> Important Notes:

This version of the System ROM contains updates aligned with the Intel IPU 2025.2 updates.

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.04.04.702 (2.30_01_06_2025).

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system Intel PCH model name is unknown in RBSU System information.

Addressed an issue where the system might log into the wrong DIMM index in the Server Configuration Lock detection log after removing the system DIMM.

Addressed an issue where the system iLORest might time out.

Addressed an issue where the system might RSOD when performing firmware update via Firmware Management Protocol.

Known Issues:

None

]]> Important Notes:

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.04.04.702 (2.30_01_06_2025).

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system Intel PCH model name is unknown in RBSU System information.

Addressed an issue where the system might log into the wrong DIMM index in the Server Configuration Lock detection log after removing the system DIMM.

Addressed an issue where the system iLORest might time out.

Addressed an issue where the system might RSOD when performing firmware update via Firmware Management Protocol.

Known Issues:

None]]>

PLDM Base (Type 0) commands comply with v1.2.0 of the PLDM base specification (DSP0240).

PLDM Platform Monitoring and Control (Type 2) commands comply with v1.3.0 of the PLDM Platform Monitoring and Control Specification (DSP0248).

Long-running task support for volume creation/deletion using Redfish and storage resource RDE action operations.

]]>

Fixed an issue where a lockup occasionally occurs when RAID 0 Predictive Spare Rebuilding (PSR) starts.

Fixed an issue where the fault LED remains lit during the rebuild process of a replaced SSD drive.

Fixed an issue where the host was unable to retrieve new configuration updates after creating a logical drive on PF drives or slow drives.

Fixed an issue where the logical volume status was incorrectly reported as OK on a secured volume if a data drive was replaced with an Otherwise Owned SED drive before reboot.

Fixed an issue where the surface scan period was not reset to default after factory reset.

Fixed an issue where the predictive failure drive did no€t fail even after the Predictive Spare Rebuild (PSR) was completed.

Fixed an issue where the Controller might have a potential lockup after a JBOD power cycle.

Fixed an issue where the offline replacement of a failed drive during a spare rebuild led to the failure of the replacement drive.

Fixed a possible lockup that could occur both during a transformation with an abrupt shutdown, and on subsequent bootup.

Fixed a potential issue where a good drive could be incorrectly marked as a predictive failure drive.

Fixed a lockup issue that could occur during I/O to a degraded volume using Smart Path.

Fixed a drive firmware update failure due to incorrect handling of sense data for specific SATA drives.

Fixed a Controller boot failure when inserted in PCIe Gen 6 systems.

Fixed issues for missing active dedicated hot spare member in HII logical drive information and failed drive part of a logical drive in the HII disk utilities.

Fixed an issue which threw wrong error code, 'InternalError’ when creating an array on controller that is waiting on adapter password.

Fixed an issue When server is powered on with no drives connected to Enclosure. Observe incorrect controller information in iLO Storage tab & Redfish

Fixed an issue that enclosures Link is missing under Storage URI in Redfish.

Fixed an issue in which drive resource does not match with Chassis for empty bay.

Fixed an issue in which incorrect severity warning of drive when sanitize erase operation is in progress.

Fixed an issue where HealthRollup shows warning during normal state.

Fixed an issue where CacheSummary.Status.Health shows incorrect during WriteCache degraded.

Fixed an issue in which PLDM/RDE Read sometimes take longer than 6s during array deletion.

]]> SR 2.9.2/SR 3.4.2 RC2

]]> Updated multi-language translation.

]]> Important Notes:

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where system may hang at POST when there are 8TB system memory and E810 NIC card installed.

Addressed an issue where the Name field of the Logical Drive under MR controller page might be missing or changed unintentionally after exiting and going back to the MR controller page.

Known Issues:

None]]> Important Notes:

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system may encounter RSOD and fail to update firmware while performing firmware update.

Known Issues:

None]]> TBD

]]> Initial release.

]]>

Added support for Azure Stack HCI 23H2

]]>

Fixes the displayed message of direct attached NVMe firmware flashing to align FW activation result by OS.

]]>

Fix for Uncorrectable Machine Check Exception (UMCE) issue which might occur.

For more information, refer to HPE Customer Advisory at the following URL: https://support.hpe.com/hpesc/public/docDisplay?docId=a00142315en_us

]]> This product fixes to align DDP with the new FW version and NVM 4.71.

]]> Initial version for VMware 9.0.

]]>

This product fixes the registry of RdmaRoceFrameSize, changing the default value from 1 to 1024.

This product fixes an issue wher the Large Send Offload(LSO) is not working.

]]> This product enhanced the compatibility with firmware of Fortville 9.5.

]]>

Added support for RHEL 10.

]]>

Fixed flashing issue through SDR method

]]>

Added support for RHEL10.

]]>

Fixed flashing issue through SDR method

]]>

Added support for Azure Stack HCI 23H2.

]]>

Added support for Microsoft Windows Server 2025.

]]>

Fix the controller library compatible issue.

]]>

Updated Supported Environments

]]>

Updated support environments

]]>

Support new Gen12 servers.

]]>

Support new Gen12 servers.

]]> Firmware for the following devices has been updated to 20.43.2026:

HPE InfiniBand HDR/Ethernet 200Gb 1-port QSFP56 PCIe3 x16 MCX653105A-HDAT Adapter - P06154-B21
HPE InfiniBand HDR100/Ethernet 100Gb 1-port QSFP56 PCIe3 x16 MCX653105A-ECAT Adapter - P06250-B21
HPE InfiniBand HDR100/Ethernet 100Gb 2-port QSFP56 PCIe3 x16 MCX653106A-ECAT Adapter - P06251-B21

No changes or new features have been included in version 20.43.2026.

]]> The following issues have been fixed in version 20.43.2026:

A linkup issue vs a 3rd party switch (BCM53405).
A reference counter issue that resulted in the firmware assertion 0x889f with CQ reference counter underflow to solve a race condition.

]]> Firmware for the following devices has been updated to 20.43.1014:

HPE InfiniBand HDR/Ethernet 200Gb 1-port QSFP56 PCIe3 x16 MCX653105A-HDAT Adapter - P06154-B21
HPE InfiniBand HDR100/Ethernet 100Gb 1-port QSFP56 PCIe3 x16 MCX653105A-ECAT Adapter - P06250-B21
HPE InfiniBand HDR100/Ethernet 100Gb 2-port QSFP56 PCIe3 x16 MCX653106A-ECAT Adapter - P06251-B21

New features and changes included in version 20.43.1014:

Added the option to indicate an error CQE event on every selected function per eSwitch manager. This indication is defined as a new WQE including the relevant information about the error (such as: syndrome, function_id, timestamp, QPs num etc.).
Extended kernel lockdown permission set. The following sub-operations can now be called by tools (permission TOOLS_RESORCES) using new HCA capability bitmask field: tool_partial_cap.

The 5 sub-operations are:

QUERY_HCA_CAP with other function
QUERY_VUID with direct data
QUERY_ROCE_ADDRESS with other vport
SET_HCA_CAP with other function
POSTPONE_CONNECTED_QP_TIMEOUT with other vport

The new added caps are:

tool_partial_cap.postpone_conn_qp_timeout_other_vport,
tool_partial_cap.set_hca_cap_other_func
tool_partial_cap.query_roce_addr_other_vport
tool_partial_cap.query_vuid_direct_data
tool_partial_cap.query_hca_cap_other_func

]]> The following issues have been fixed in version 20.43.1014:

Setup crash when "create_sq" used invalid mbox.
The firmware always returned the "next" value to be applied when querying FACTORY default NV configuration values.

]]> SR 2.9.2 patch 1

]]>

Added support for saving Managed SED master key and reset key in cipher text in controller NVRAM instead of clear text.

Changed temperature polling period from 1 minute to 5 minutes for HBA mode drives that are in low power state.

Added support for clearing UREs in unmapped LBA range of fault tolerant logical drives.

Improved random write and mixed read-write performance.

Added support for SED encryption configuration through Redfish interface.

Added support of Redfish Chassis implementation for UBM Backplanes.

Added Redfish ACTION:

Storage.SetEncryptionKey

Added support for Redfish property PATCH:

Storage.EncryptionMode
Storage.HotspareActivationPolicy
Drive.HostspareReplacementMode
Drive.HotspareType
Volume.Encrypted

Added support for Redfish Status.Conditions property to resources:

Drive
Port
StorageController
StorageController.CacheSummary
Volume

Added support for Redfish properties:

Drive.DriveFormFactor
Drive.FirmwareVersion
Drive.Manufacture (SAS only)
Drive.SlotCapableProtocols
StorageController.AssetTag
StorageController.Links.PCIeFunction
Volume.BlockSizeBytes
Volume.LogicalUnitNumber

Added support for PLDM Type5 UBM PIC firmware flashing behind expander.

]]>

Fixed an issue where the host experienced BSOD while clearing the controller configuration.

Fixed controller lockups caused by incorrect address reads and partial RAM initialization for PCIe functions, leading to ECC errors.

Fixed issues with external storage.

Fixed issues with the SATA drive.

Fixed issues with the SED drive.

Fixed issues with the spare drive.

Corrected MCTP-related issues.

Fixed surface scan issues on the RAID 50.

Fixed issues encountered during heavy I/O operations.

Fixed volume issues on the failed drive.

Fixed issues for incorrect Severity reported in Redfish events.

Fixed issues for incorrect Status reported in Redfish resources.

Fixed an issue with improper capacity information in Redfish drive Name.

Fixed an issue where Redfish long running task status is not reported.

Fixed an issue where DurableNameFormat for RAID volumes are reported as UUID in RDE READ operations, but should be NAA.

Fixed an issue where failed to take ownership of, or to revert, a SED through Redfish.

Fixed an issue when a drive hosting a RAID 0 Volume is removed and reinserted, a VolumeOK event is not generated.

]]> This Firmware package contains following firmware versions:

Adapter	Speed	Universal Boot Image	Firmware	UEFI	Boot Bios
HPE SN1200E 16Gb Dual Port Fibre Channel Host Bus Adapter	16Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1200E 16Gb Single Port Fibre Channel Host Bus Adapter	16Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1600E 32Gb Dual Port Fibre Channel Host Bus Adapter	32Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1600E 32Gb Single Port Fibre Channel Host Bus Adapter	32Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1610E 32Gb Single Port Fibre Channel Host Bus Adapter	32Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1610E 32Gb Dual Port Fibre Channel Host Bus Adapter	32Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1700E 64Gb Single Port Fibre Channel Host Bus Adapter	64Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1700E 64Gb Dual Port Fibre Channel Host Bus Adapter	64Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0

]]> This Firmware package contains following firmware versions:

Adapter	Speed	Universal Boot Image	Firmware	UEFI	Boot Bios
HPE SN1200E 16Gb Dual Port Fibre Channel Host Bus Adapter	16Gb	14.4.329.10	14.4.329.10	14.4.329.9	14.4.290.0
HPE SN1200E 16Gb Single Port Fibre Channel Host Bus Adapter	16Gb	14.4.329.10	14.4.329.10	14.4.329.9	14.4.290.0
HPE SN1600E 32Gb Dual Port Fibre Channel Host Bus Adapter	32Gb	14.4.329.10	14.4.329.10	14.4.329.9	14.4.290.0
HPE SN1600E 32Gb Single Port Fibre Channel Host Bus Adapter	32Gb	14.4.329.10	14.4.329.10	14.4.329.9	14.4.290.0
HPE SN1610E 32Gb Single Port Fibre Channel Host Bus Adapter	32Gb	14.4.329.10	14.4.329.10	14.4.329.9	14.4.290.0
HPE SN1610E 32Gb Dual Port Fibre Channel Host Bus Adapter	32Gb	14.4.329.10	14.4.329.10	14.4.329.9	14.4.290.0
HPE SN1700E 64Gb Single Port Fibre Channel Host Bus Adapter	64Gb	14.4.329.10	14.4.329.10	14.4.329.9	14.4.290.0
HPE SN1700E 64Gb Dual Port Fibre Channel Host Bus Adapter	64Gb	14.4.329.10	14.4.329.10	14.4.329.9	14.4.290.0

]]> Important Notes:

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Enhancements/New Features:

This version is in compliance with IPU 2025.1 guidance.

Known Issues:

None]]> Important Notes:

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Enhancements/New Features:

This version is in compliance with IPU 2025.1 guidance.

Known Issues:

None]]> Important Notes:

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Enhancements/New Features:

This version is in compliance with IPU 2025.1 guidance.

Known Issues:

None]]> Important Notes:

This version of the Server Platform Services (SPS) Firmware contains updates aligned with the Intel Product Update (IPU) version IPU.2024.1 guidance. This version of the SPS should be paired with System ROM 2.00 (02/01/2024) or later.

Firmware Dependencies:

None

Enhancements/New Features:

This version is in compliance with IPU.2024.1 guidance.

Known Issues:

None]]> Support ESXi8.0

]]>

Support HPE ProLiant DL325 Gen10 Plus Server

]]>

Added support for Azure Stack HCI 23H2

]]>

Fixes the displayed message of direct attached NVMe firmware flashing to align FW activation result by OS.

]]>

Added support for Microsoft Windows Server 2025.

]]>

Fix the controller library compatible issue.

]]> Important Notes:

This revision of the System ROM includes AMD reference code RomePI 1.0.0.M for AMD 2nd Generation EPYC processors. This revision of the System ROM includes AMD reference code NaplesPI 1.0.0.Q for AMD 1st Generation EPYC processors.

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Enhancements/New Features:

This revision of the System ROM includes AMD reference code RomePI 1.0.0.M for AMD 2nd Generation EPYC processors.

This revision of the System ROM includes AMD reference code NaplesPI 1.0.0.Q for AMD 1st Generation EPYC processors.

Known Issues:

None]]> Important Notes:

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Enhancements/New Features:

Added pop-up message for all Intelligent Provisioning boot paths to warn users of the risk of data loss.

Known Issues:

None]]>

Added Support for ESXi 9.0

]]>

Fix the controller library compatible issue.

]]>

Added RHEL10 support

]]> N/A.

]]> This product fixes to update the INF file to enable the DmaRemappingCompatible feature with a value of 3.

]]> This product enhanced the compatibility with firmware of Fortville 9.5.

]]> Important Notes:

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Enhancements/New Features:

This version is in compliance with IPU 2025.1 guidance.

Known Issues:

None]]> Important Notes:

This version of the Server Platform Services (SPS) Firmware contains updates aligned with the Intel Product Update (IPU) version IPU.2023.3 guidance.

Firmware Dependencies:

None

Enhancements/New Features:

This version is in compliance with Intel IPU.2023.3 guidance.

Known Issues:

None]]>

Added support for ESXi 9.0

]]>

Fix the controller library compatible issue.

]]>

Added RHEL10 support

]]> N/A.

]]>

Updated supported environments

]]>

Updated supported environments

]]>

Added support for Azure Stack HCI 23H2.

]]>

Fix the controller library compatible issue.

]]>

Added support for Microsoft Windows Server 2025.

]]>

Fix the controller library compatible issue.

]]> Important Notes:

This version of the System ROM contains updates aligned with the Intel IPU 2025.2 updates.

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.04.04.702 (2.30_01_06_2025).

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system Intel PCH model name is unknown in RBSU System information.

Addressed an issue where the system might log into the wrong DIMM index in the Server Configuration Lock detection log after removing the system DIMM.

Addressed an issue where the system iLORest might time out.

Addressed an issue where the system might RSOD when performing firmware update via Firmware Management Protocol.

Addressed an issue where CPU power readings displayed in iLO were unbalanced between two processors.

Known Issues:

None

]]> Important Notes:

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.04.04.702 (2.30_01_06_2025).

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system Intel PCH model name is unknown in RBSU System information.

Addressed an issue where the system might log into the wrong DIMM index in the Server Configuration Lock detection log after removing the system DIMM.

Addressed an issue where the system iLORest might time out.

Addressed an issue where the system might RSOD when performing firmware update via Firmware Management Protocol.

Known Issues:

None]]>

Support new Gen 12 servers.

]]>

Support new servers.

]]>

Added Support for ESXi 9.0

]]>

Fix the controller library compatible issue.

]]> Updated multi-language translation.

]]> Important Notes:

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system may encounter RSOD and fail to update firmware while performing firmware update.

Addressed an issue where the Name field of the Logical Drive under MR controller page might be missing or changed unintentionally after exiting and going back to the MR controller page.

Known Issues:

None]]> Important Notes:

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.00.03.700 (2.30_01_07_2025).

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system might RSOD when performing firmware update via Firmware Management Protocol.

Known Issues:

None]]> Firmware for the following devices has been updated to 20.43.2026:

HPE InfiniBand HDR/Ethernet 200Gb 1-port QSFP56 PCIe3 x16 MCX653105A-HDAT Adapter - P06154-B21
HPE InfiniBand HDR100/Ethernet 100Gb 1-port QSFP56 PCIe3 x16 MCX653105A-ECAT Adapter - P06250-B21
HPE InfiniBand HDR100/Ethernet 100Gb 2-port QSFP56 PCIe3 x16 MCX653106A-ECAT Adapter - P06251-B21

No changes or new features have been included in version 20.43.2026.

]]> The following issues have been fixed in version 20.43.2026:

A linkup issue vs a 3rd party switch (BCM53405).
A reference counter issue that resulted in the firmware assertion 0x889f with CQ reference counter underflow to solve a race condition.

]]> Firmware for the following devices has been updated to 20.42.1000:

HPE InfiniBand HDR/Ethernet 200Gb 1-port QSFP56 PCIe3 x16 MCX653105A-HDAT Adapter - P06154-B21
HPE InfiniBand HDR100/Ethernet 100Gb 1-port QSFP56 PCIe3 x16 MCX653105A-ECAT Adapter - P06250-B21
HPE InfiniBand HDR100/Ethernet 100Gb 2-port QSFP56 PCIe3 x16 MCX653106A-ECAT Adapter - P06251-B21

New features and changes included in version 20.42.1000:

Added a new command interface "Memory slow release" to enable/disable holding memory pages for a defined period of time. Once the timer expires, the firmware will return the pages to the driver.
Added support for MVTS register via a miscellaneous driver using the access_register PRM command.

]]> The following issues have been fixed in version 20.42.1000:

RDE PortMetrics property Transceivers.SupplyVoltage was reflected in incorrect units of 100uV instead of V.
HCA_CAP allowed rogue drivers to create more EQs than the number allowed in the HCA_CAP.max_num_eqs.
Incorrect MPLS packets discards flow when the GLOBAL pause capability was disabled.

]]> This product fixes to align DDP with the new FW version and NVM 4.71.

]]> This product is now supported on a new platform.

]]>

Added support for Azure Stack HCI 23H2..

]]>

Fix the controller library compatible issue.

]]>

Added support for ESXi 9.0.

]]>

Fixes the potential drive hang issue after POH exceed 6.5 years. We suggest customers to update the FW as soon as possible to prevent inconvenience.

For more information, CB is published at the following URL: https://support.hpe.com/hpesc/public/docDisplay?docId=a00142174en_us

]]>

Added support for ESXi 9.0

]]>

Fix to Assert fixes, current firmware improvements and bug fixes.

]]>

Added support for ESXi 9.0

]]>

Fixes the displayed message of direct attached NVMe firmware flashing to align FW activation result by OS.

]]>

Fix for Uncorrectable Machine Check Exception (UMCE) issue which might occur.

For more information, refer to HPE Customer Advisory at the following URL: https://support.hpe.com/hpesc/public/docDisplay?docId=a00142315en_us

]]>

Support Azure Stack HCI 23H2 OS.

Support new Gen12 servers.

]]>

Support Azure Stack HCI 23H2 OS.

Support new Gen12 servers.

]]> Updated to driver version 14.2.537.0

The raw driver files can be obtained by extracting the Smart Component and then extracting the Emulex installer. Use this command:

elxdrvr-fc-version.exe /q2 extract=2

The extracted files are located:

C:\Users\Administrator\Documents\Emulex\Drivers\FC-version

Each kit folder has subsequent architecture folders with subsequent OS folders. For example,

C:\Users\Administrator\Documents\Emulex\Drivers\FC-version\x64\win2019

Fixed the following:

Apps AutoPilot installer Windows (from 14.2.555.0 to 14.2.589.31),
APInstall fails on Win 2019 Server Core. unable to find library oledlg.dll

]]> Fixed the following:

Apps AutoPilot installer Windows (from 14.2.555.0 to 14.2.589.31),
APInstall fails on Win 2019 Server Core. unable to find library oledlg.dll

]]> Updated to driver version 14.2.537.0

The raw driver files can be obtained by extracting the Smart Component and then extracting the Emulex installer. Use this command:

elxdrvr-fc-version.exe /q2 extract=2

The extracted files are located:

C:\Users\Administrator\Documents\Emulex\Drivers\FC-version

Each kit folder has subsequent architecture folders with subsequent OS folders. For example,

C:\Users\Administrator\Documents\Emulex\Drivers\FC-version\x64\win2019

]]> Firmware for the following devices has been updated to 12.28.2302:

825110-B21 (HPE InfiniBand EDR/Ethernet 100Gb 1-port 840QSFP28 Adapter)
825111-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 840QSFP28 Adapter)

Firmware for the following devices has been updated to 16.35.4506:

879482-B21 (HPE InfiniBand FDR/Ethernet 40/50Gb 2-port 547FLR-QSFP Adapter)
872726-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 841QSFP28 Adapter)

No new Features and changes included in version 12.28.2302.

New features and changes included in version 16.35.4506:

Added address validation in MLNX OEM CMD 0x0032 (get debug info) to be 4- bytes aligned.

]]> No new fixes have been added in version 12.28.2302.

The following issues have been fixed in version 16.35.4506:

Incorrect MPLS packets discards flow occurred when the GLOBAL pause capability was disabled.

]]> Firmware for the following devices has been updated to 12.28.2302:

825110-B21 (HPE InfiniBand EDR/Ethernet 100Gb 1-port 840QSFP28 Adapter)
825111-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 840QSFP28 Adapter)

Firmware for the following devices has been updated to 16.35.4030:

879482-B21 (HPE InfiniBand FDR/Ethernet 40/50Gb 2-port 547FLR-QSFP Adapter)
872726-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 841QSFP28 Adapter)

Changes included in component version 1.0.0.16(A):

Added support for Azure Stack HCI 23H2 in the component metadata.

No new Features and changes included in version 12.28.2302.

New features and changes included in version 16.35.4030:

Added support for postponing QP timeout "retry exceeded" errors for traffic directed at specific destinations. This new capability prevents broken connections for destinations in downtime because of live migration.

]]> No new fixes have been added in version 12.28.2302.

The following issues have been fixed in version 16.35.4030:

VF FLR would get stuck when its PF triggered the FLR as well.
Unexpected source UDP port appeared in RoCE packets when the firmware ignored a non-PF driver configuration for RoCE source UDP port control (as set in SET_HCA_CAP.sw_r_roce_src_udp_port).

]]> This product now supports Red Hat Enterprise Linux 9.5.

]]> This product fixes the kernel compilation issue.

]]> This product is now supported on a new platform.

]]> Removed Expired SUSE and Vmware Certificates.

Improved detection and interaction with certain PCIe cards during UEFI HBA discovery process.

]]> Important Notes:

This version of the System ROM contains updates aligned with the Intel IPU 2025.2 updates.

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.01.05.105.

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system might have false IML message "Processor X, DIMM Y - This NVDIMM is NOT a HPE SmartMemory NVDIMM".

Addressed an issue where the system might trigger BitLocker Recovery after reboot.

Known Issues:

None

]]> Removed Expired SUSE and Vmware Certificates.

Improved detection and interaction with certain PCIe cards during UEFI HBA discovery process.

]]> Important Notes:

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.01.05.105.

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system might have false IML message "Processor X, DIMM Y - This NVDIMM is NOT a HPE SmartMemory NVDIMM".

Addressed an issue where the system might trigger BitLocker Recovery after reboot.

Known Issues:

None]]> Removed Expired SUSE and Vmware Certificates.

Improved detection and interaction with certain PCIe cards during UEFI HBA discovery process.

]]> Important Notes:

This version of the System ROM contains updates aligned with the Intel IPU 2025.2 updates.

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.01.05.105.

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system might have false IML message "Processor X, DIMM Y - This NVDIMM is NOT a HPE SmartMemory NVDIMM".

Addressed an issue where the system might trigger BitLocker Recovery after reboot.

Known Issues:

None

]]> Removed Expired SUSE and Vmware Certificates.

Improved detection and interaction with certain PCIe cards during UEFI HBA discovery process.

]]> Important Notes:

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.01.05.105.

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system might have false IML message "Processor X, DIMM Y - This NVDIMM is NOT a HPE SmartMemory NVDIMM".

Addressed an issue where the system might trigger BitLocker Recovery after reboot.

Known Issues:

None]]> Fixed online force flash issue on OneView.

]]>

Added Azure Stack HCI 23H2 support

]]> Driver version 5.5.85.0
This driver is only supported on VMware ESXi 9.0

]]> Driver version 5.4.83.1
This driver is only supported on VMware ESXi 9.0

]]>

Added support for ESXi 9.0

]]>

Fix the controller library compatible issue.

]]> Removed Expired SUSE and Vmware Certificates.

Improved detection and interaction with certain PCIe cards during UEFI HBA discovery process.

]]> Important Notes:

This version of the System ROM contains updates aligned with the Intel IPU 2025.2 updates.

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.01.05.105.

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system might have false IML message "Processor X, DIMM Y - This NVDIMM is NOT a HPE SmartMemory NVDIMM".

Addressed an issue where the system might trigger BitLocker Recovery after reboot.

Known Issues:

None

]]> Removed Expired SUSE and Vmware Certificates.

Improved detection and interaction with certain PCIe cards during UEFI HBA discovery process.

]]> Important Notes:

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.01.05.105.

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system might have false IML message "Processor X, DIMM Y - This NVDIMM is NOT a HPE SmartMemory NVDIMM".

Addressed an issue where the system might trigger BitLocker Recovery after reboot.

Known Issues:

None]]> Important : Security Hardening Enhancements - This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your device firmware to this version to improve the firmware security and reliability of your device.

New features and changes included in version 16.35.4506:

Added address validation in MLNX OEM CMD 0x0032 (get debug info) to be 4- bytes aligned.

]]> The following issues have been fixed in version 16.35.4506:

Incorrect MPLS packets discards flow occurred when the GLOBAL pause capability was disabled.

New features and changes included in version 16.35.4030:

Added support for postponing QP timeout "retry exceeded" errors for traffic directed at specific destinations. This new capability prevents broken connections for destinations in downtime because of live migration.

]]> The following issues have been fixed in version 16.35.4030:

VF FLR would get stuck when its PF triggered the FLR as well.
Unexpected source UDP port appeared in RoCE packets when the firmware ignored a non-PF driver configuration for RoCE source UDP port control (as set in SET_HCA_CAP.sw_r_roce_src_udp_port).

]]> Added Support for RHEL 10

]]>

Fixed flashing issue through SDR method

]]>

Added support for ESXi 9.0

]]>

Fixes the logic bug in the media cache cleaning abort handling that caused the drive to choose and execute the R/W command before the Request Sense to prevent assert.

Adding other logging and FW enhancements.

]]>

Added support for ESXi 9.0

]]>

Fix the controller library compatible issue.

]]>

Added support for Azure Stack HCI 23H2.

]]>

Fix the controller library compatible issue.

]]>

This product fixes an issue where the speed may be downgraded to Gen3.

This product fixes an issue where the Linux driver fails to load due to an EEPROM checksum error when the RDE:MACAddress property is patched.

This product fixes an issue where the NIC is not detected after performing the RDE patch operation on NetworkDeviceFunctions settings.

This product fixes an issue where the RDE: Setting property (AutoSpeedNegotiationEnabled) does not cause the property value to update, returning a code 400.

This product fixes an issue where the RDE fails to perform the get operation when the adapter is configured as pass-through.

This product fixes an issue where the RDE property (FlowControlStatus) does not report the correct status after the RDE property FlowControlConfiguration is set to Tx.

This product fixes an issue where the RDE patch operation fails on the AutoSpeedNegotiationEnabled property.

]]> Add new support platform.

]]>

This product fixes an issue where the speed may be downgraded to Gen3.

This product fixes an issue where the Linux driver fails to load due to an EEPROM checksum error when the RDE:MACAddress property is patched.

This product fixes an issue where the NIC is not detected after performing the RDE patch operation on NetworkDeviceFunctions settings.

This product fixes an issue where the RDE: Setting property (AutoSpeedNegotiationEnabled) does not cause the property value to update, returning a code 400.

This product fixes an issue where the RDE fails to perform the get operation when the adapter is configured as pass-through.

This product fixes an issue where the RDE property (FlowControlStatus) does not report the correct status after the RDE property FlowControlConfiguration is set to Tx.

This product fixes an issue where the RDE patch operation fails on the AutoSpeedNegotiationEnabled property.

]]> This product now supports Intel E810-XXVDA4 Ethernet 10/25Gb 4-port SFP28 MCLK NG Adapter for HPE and new support platform.

]]>

Added support for Azure Stack HCI 23H2.

]]>

Added support for Microsoft Windows Server 2025.

]]>

Fix the controller library compatible issue.

]]> This product fixes to update the INF file to enable the DmaRemappingCompatible feature with a value of 2.

]]> This product now supports Azure Stack HCI OS.

]]> Removed Expired SUSE and Vmware Certificates.

Improved detection and interaction with certain PCIe cards during UEFI HBA discovery process.

]]> Important Notes:

This version of the System ROM contains updates aligned with the Intel IPU 2025.2 updates.

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.01.05.105.

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system might have false IML message "Processor X, DIMM Y - This NVDIMM is NOT a HPE SmartMemory NVDIMM".

Addressed an issue where the system might trigger BitLocker Recovery after reboot.

Known Issues:

None

]]> Removed Expired SUSE and Vmware Certificates.

Improved detection and interaction with certain PCIe cards during UEFI HBA discovery process.

]]> Important Notes:

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.01.05.105.

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system might have false IML message "Processor X, DIMM Y - This NVDIMM is NOT a HPE SmartMemory NVDIMM".

Addressed an issue where the system might trigger BitLocker Recovery after reboot.

Known Issues:

None]]>

Added support for ESXi 9.0

]]>

Fixes Maximum Temperature Reporting in system log.

]]>

Added support for Azure Stack HCI 23H2

]]>

Fix the controller library compatible issue.

]]>

Added support for Microsoft Windows Server 2025.

]]>

Fix the controller library compatible issue.

]]> Added Support for RHEL 10.

]]>

Fixed flashing issue through SDR method

]]>

Added support for Azure Stack HCI 23H2

]]>

Fixes the displayed message of direct attached NVMe firmware flashing to align FW activation result by OS.

]]>

Added support for Microsoft Windows Server 2025.

]]>

Fix the controller library compatible issue.

]]> Removed Expired SUSE and Vmware Certificates.

Improved detection and interaction with certain PCIe cards during UEFI HBA discovery process.

]]> Important Notes:

This version of the System ROM contains updates aligned with the Intel IPU 2025.2 updates.

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.01.05.105.

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system might have false IML message "Processor X, DIMM Y - This NVDIMM is NOT a HPE SmartMemory NVDIMM".

Addressed an issue where the system might trigger BitLocker Recovery after reboot.

Known Issues:

None

]]> Removed Expired SUSE and Vmware Certificates.

Improved detection and interaction with certain PCIe cards during UEFI HBA discovery process.

]]> Important Notes:

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.01.05.105.

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system might have false IML message "Processor X, DIMM Y - This NVDIMM is NOT a HPE SmartMemory NVDIMM".

Addressed an issue where the system might trigger BitLocker Recovery after reboot.

Known Issues:

None]]>

Updated supported environments

]]>

Updated SBOM requirement

]]> TBD

]]> This product corrects an issue which system crashed due to hardware error.

]]>

Added support for RHEL10.

]]>

Fixes the displayed message of direct attached NVMe firmware flashing to align FW activation result by OS.

]]> Important Notes:

This version of the System ROM contains updates aligned with the Intel IPU 2025.2 updates.

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.04.04.702 (2.30_01_06_2025).

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system Intel PCH model name is unknown in RBSU System information.

Addressed an issue where the system might log into the wrong DIMM index in the Server Configuration Lock detection log after removing the system DIMM.

Addressed an issue where the system iLORest might time out.

Addressed an issue where the system might RSOD when performing firmware update via Firmware Management Protocol.

Known Issues:

None

]]> Important Notes:

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.04.04.702 (2.30_01_06_2025).

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system Intel PCH model name is unknown in RBSU System information.

Addressed an issue where the system might log into the wrong DIMM index in the Server Configuration Lock detection log after removing the system DIMM.

Addressed an issue where the system iLORest might time out.

Addressed an issue where the system might RSOD when performing firmware update via Firmware Management Protocol.

Known Issues:

None]]> Updated Driver version 10.02.13.03-k1

]]> Added support for:

RedHat Enterprise Linux 9.5

Updated to driver version 10.02.12.01-k1

]]> TBD

]]>

This product enhances to update the installation location for nicclilom to the correct path.

This product enhances functionality by querying DCB settings when the NETDEV_CHANGE event occurs.

]]>

This product has fixed the ETS validation issue to prevent traffic class (TC) starvation caused by incorrect bandwidth allocation.

This product fixes the issue where debugfs qp_info displays the UDP source port value incorrectly.

This product fixes the issue where the device fails to unregister from PTP during shutdown or suspend.

This product fixes the issue where IPv6 VXLAN decapsulation was not properly supported.

This product fixes the issue where out-of-sequence (OOS) packets were being dropped.

This product fixes the issue where flow priority levels 0–3 were not handled correctly.

This product fixes the issue where the coredump file decoder crashes when generating a coredump summary.

]]> Important Notes:

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Enhancements/New Features:

This revision of the System ROM includes AMD reference code RomePI 1.0.0.M for AMD 2nd Generation EPYC processors.

This revision of the System ROM includes AMD reference code NaplesPI 1.0.0.Q for AMD 1st Generation EPYC processors.

Known Issues:

None]]> Important Notes:

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Enhancements/New Features:

Added pop-up message for all Intelligent Provisioning boot paths to warn users of the risk of data loss.

Known Issues:

None

]]>

Added support for Azure Stack HCI 23H2

]]>

Fix the controller library compatible issue.

]]>

Added support for Microsoft Windows Sever 2025.

]]>

Fix the controller library compatible issue.

]]>

Added support for RHEL 10.

]]>

Fixed flashing issue through SDR method

]]> TBD

]]> This product fixed to prevent BSOD issue.

]]>

Added support for ESXi 9.0

]]>

Fix the controller library compatible issue.

]]>

Added support for RHEL 10.

]]>

Fixed flashing issue through SDR method

]]> This product fixes the wording of "Ndis Poll Mode" and "Encapsulation Overhead," including both English and other translations.

]]> This product enhanced the compatibility with firmware of Fortville 9.5.

]]>

Added support for RHEL10.

]]>

Fixed flashing issue through SDR method

]]>

Added support for ESXi 9.0

]]>

Fix the controller library compatible issue.

]]> Initial version.

]]> This product fixes the wording of "Ndis Poll Mode" and "Encapsulation Overhead," including both English and other translations.

]]> This product enhanced the compatibility with firmware of Fortville 9.5.

]]> Upgraded to version 26.43.1014

]]>

Added support for Azure Stack HCI 23H2.

]]>

Fix the controller library compatible issue.

]]> NMST version 4.31.0.150

This version is supported on VMware ESXi 9 Update 0 only.

]]> This Firmware package contains following firmware versions:

Adapter	Speed	Universal Boot Image	Firmware	UEFI	Boot Bios
HPE SN1200E 16Gb Dual Port Fibre Channel Host Bus Adapter	16Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1200E 16Gb Single Port Fibre Channel Host Bus Adapter	16Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1600E 32Gb Dual Port Fibre Channel Host Bus Adapter	32Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1600E 32Gb Single Port Fibre Channel Host Bus Adapter	32Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1610E 32Gb Single Port Fibre Channel Host Bus Adapter	32Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1610E 32Gb Dual Port Fibre Channel Host Bus Adapter	32Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1700E 64Gb Single Port Fibre Channel Host Bus Adapter	64Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0
HPE SN1700E 64Gb Dual Port Fibre Channel Host Bus Adapter	64Gb	14.4.473.14	14.4.473.14	14.4.473.8	14.4.469.0

]]> Updated multi-language translation.

]]> Important Notes:

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where system may hang at POST when there are 8TB system memory and E810 NIC card installed.

Addressed an issue where the Name field of the Logical Drive under MR controller page might be missing or changed unintentionally after exiting and going back to the MR controller page.

Known Issues:

None]]> Important Notes:

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system may encounter RSOD and fail to update firmware while performing firmware update.

Known Issues:

None]]> Added Support for RHEL 10

]]>

Fixed flashing issue through SDR method

]]> The following new features and changes have been included in version 25.01-0.6.0.1

[ConnectX-7] Multi-host LAG: When using a multi-host deployment, each host is assigned unique ports and PFs and manages its own LAG.
Hardware GRO: Hardware Generic Receive Offload (GRO) reduces CPU overhead and improves throughput by offloading the task of reassembling incoming network packets from the CPU.
Precision Time Measurement (PTM): Precision Time Measurement (PTM) enhances clock synchronization accuracy between the NIC's hardware clock and the system's host clock. It addresses inaccuracies caused by asymmetric PCIe request and response times, which can affect PTP.
Transport RDMA Steering Domain: Transport RDMA steering domain in the kernel allows users to create steering tables and rules using the new domain types FS_FT_RDMA_TRANSPORT_RX and FS_FT_RDMA_TRANSPORT_TX, with support for both DevX commands and the added functionality in mlx5dv_create_flow_matcher().
DevX QPs Parallel Cleanup: Reduces cleanup (kill) time of user-space applications that use DevX QPs, without requiring any changes on the user's end. When using a kernel that includes this patch, DevX QP destruction upon cleanup will be sent to the firmware in parallel, rather than serially as before, resulting in faster cleanup times. The more DevX QPs the application has, the more noticeable the improvement will be.
Flow Control for Solicited MADs: Implements flow control for solicited MADs in the MAD layer to prevent loss due to insufficient resources at the receiver. Both the client and server function as receivers: the server handles incoming requests, while the client receives the responses.
Increased the default TX queue length in IPoIB to enhance qdisc queueing and reduce CPU spikes.
The "--defltprio" flag has been deprecated and removed from the mlnx_qos tool.

]]> The following issues have been fixed in version 25.01-0.6.0.1:

Incorrect SA switching when multiple active TX SAs are created on a SC, caused by failing to respect the SA configured by "encoding_sa".
Incorrect receive queue cache size calculation.

]]> The following new features and changes have been included in version 24.10-1.1.4.1:

Enhanced firmware reset flow for Sync1 utilizing community-accepted hot reset kernel flow.

]]> The following issues have been fixed in version 24.10-1.1.4.1:

rte_eth_dev_start() performed unnecessary recreation of mlx5 control flow rules, resulting in increased delay of rte_eth_dev_start().
Firefly was not compliant with "SyncE to 1pps Class B/C Transient response" while using ConnectX7 FHHL adapter card.

]]>

Added RHEL10 support

]]>

Added Write Cache Status field to the info page for physical drives when "pd all show detail" is used.

]]>

Corrected wrong wording of Parity Initialization messages.

Fixed vulnerability CVE-2023-45853.

]]> This product fixes an issue where Large Send Offload (LSO) is not working.

]]> Initial version.

]]> This product fixes an issue where Large Send Offload (LSO) is not working.

]]> This product is now supported on a new platform.

]]>

Added support for ESXi 9.0

]]>

Fixes the potential drive hang issue after POH exceed 6.5 years. We suggest customers to update the FW as soon as possible to prevent inconvenience.

For more information, refer to HPE Customer Bulletin at the following URL: https://support.hpe.com/hpesc/public/docDisplay?docId=a00142174en_us

]]>

Added support for Azure Stack HCI 23H2.

]]>

Fix the controller library compatible issue.

]]> Firmware for the following devices has been updated to 20.43.2026:

HPE InfiniBand HDR/Ethernet 200Gb 1-port QSFP56 PCIe3 x16 MCX653105A-HDAT Adapter - P06154-B21
HPE InfiniBand HDR100/Ethernet 100Gb 1-port QSFP56 PCIe3 x16 MCX653105A-ECAT Adapter - P06250-B21
HPE InfiniBand HDR100/Ethernet 100Gb 2-port QSFP56 PCIe3 x16 MCX653106A-ECAT Adapter - P06251-B21

No changes or new features have been included in version 20.43.2026.

]]> The following issues have been fixed in version 20.43.2026:

A linkup issue vs a 3rd party switch (BCM53405).
A reference counter issue that resulted in the firmware assertion 0x889f with CQ reference counter underflow to solve a race condition.

]]> Firmware for the following device has been updated to 14.32.1900:

P11338-B21 (HPE Ethernet 10Gb 2-port 548SFP+ Adapter)

New features and changes included in version 1.0.0.7(A):

Added support for Azure Stack HCI 23H2.

No new features or changes have been included in firmware version 14.32.1900.

]]> No fixes have been included in firmware version 14.32.1900.

]]> Firmware for the following device has been updated to 14.32.1900:

P11338-B21 (HPE Ethernet 10Gb 2-port 548SFP+ Adapter)

No new features or changes have been included in firmware version 14.32.1900.

]]> No fixes have been included in firmware version 14.32.1900.

]]>

Added support for ESXi 9.0

]]>

Fix the controller library compatible issue.

]]> Updated multi-language translation.

Removed Expired SUSE and Vmware Certificates.

]]> Important Notes:

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the Name field of the Logical Drive under MR controller page might be missing or changed unintentionally after exiting and going back to the MR controller page.

Known Issues:

None]]> Added pop-up message for all Intelligent Provisioning boot paths to warn users of the risk of data loss.

]]> Important Notes:

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system iLO remote console might hang when the System Utilities Language is set to Japanese.

Known Issues:

None

]]>

Added support for RHEL 10.

]]>

Fixed flashing issue through SDR method

]]>

fix for genericmsi version

]]>

Added Write Cache Status field to the info page for physical drives when "pd all show detail" is used.

]]>

Corrected wrong wording of Parity Initialization messages.

Fixed vulnerability CVE-2023-45853.

]]> Driver version 5.4.85.0-1
This driver is only supported on VMware ESXi 8.0u3

]]> Driver version 5.4.83.1
This driver is only supported on VMware ESXi 8.0u3

]]> TBD

]]>

This product removes the Ethernet/LLDPTransmit/ManagementVlanId property to streamline configuration.

This product enhances the coredump feature in the BNXT driver for improved diagnostics.

This product enhances to update the driver to suppress the HII MBA menu for a cleaner interface.

]]>

This product fixes the issue where RDMA connections are not getting connected.

This product fixes the issue where RoCE and TX/RX path core dump decoding failed.

This product fixes the issue where Port 1 was not receiving broadcast packets with ESXi.

This product fixes the issue where the OCP module experiences link width degradation in the system.

This product fixes the issue where PXE boot does not work with VLAN configurations.

]]>

Added support for Azure Stack HCI 23H2.

]]>

Fix the controller library compatible issue.

]]> Added support for:

Red Hat Enterprise Linux 10.0

Updated to version 14.4.473.24

]]> Updated to version 14.4.473.7

]]> Updated multi-language translation.

]]> Important Notes:

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where system may hang at POST when there are 8TB system memory and E810 NIC card installed.

Addressed an issue where the Name field of the Logical Drive under MR controller page might be missing or changed unintentionally after exiting and going back to the MR controller page.

Known Issues:

None]]> Important Notes:

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system may encounter RSOD and fail to update firmware while performing firmware update.

Known Issues:

None]]>

Added support for ESXi 9.0

]]>

Fix the controller library compatible issue.

]]>

Added support for RHEL 10.

]]>

Fixed flashing issue through SDR method

]]> Updated to driver version 24.10.26603.0

]]>

Fixes the displayed message of direct attached NVMe firmware flashing to align FW activation result by OS.

]]>

Fix the controller library compatible issue.

]]> Removed Expired SUSE and Vmware Certificates.

Improved detection and interaction with certain PCIe cards during UEFI HBA discovery process.

]]> Important Notes:

This version of the System ROM contains updates aligned with the Intel IPU 2025.2 updates.

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.01.05.105.

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system might have false IML message "Processor X, DIMM Y - This NVDIMM is NOT a HPE SmartMemory NVDIMM".

Addressed an issue where the system might trigger BitLocker Recovery after reboot.

Known Issues:

None

]]> Removed Expired SUSE and Vmware Certificates.

Improved detection and interaction with certain PCIe cards during UEFI HBA discovery process.

]]> Important Notes:

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.01.05.105.

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system might have false IML message "Processor X, DIMM Y - This NVDIMM is NOT a HPE SmartMemory NVDIMM".

Addressed an issue where the system might trigger BitLocker Recovery after reboot.

Known Issues:

None]]>

Added support for ESXi 9.0

]]>

Fixes the displayed message of direct attached NVMe firmware flashing to align FW activation result by OS.

]]>

Fix the controller library compatible issue.

]]> Initial release

]]>

This product fixes an issue where the speed may be downgraded to Gen3.

This product fixes an issue where the Linux driver fails to load due to an EEPROM checksum error when the RDE:MACAddress property is patched.

This product fixes an issue where the NIC is not detected after performing the RDE patch operation on NetworkDeviceFunctions settings.

This product fixes an issue where the RDE: Setting property (AutoSpeedNegotiationEnabled) does not cause the property value to update, returning a code 400.

This product fixes an issue where the RDE fails to perform the get operation when the adapter is configured as pass-through.

This product fixes an issue where the RDE property (FlowControlStatus) does not report the correct status after the RDE property FlowControlConfiguration is set to Tx.

This product fixes an issue where the RDE patch operation fails on the AutoSpeedNegotiationEnabled property.

]]> Add new support platform.

]]> Updated multi-language translation.

]]> Important Notes:

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where system may hang at POST when there are 8TB system memory and E810 NIC card installed.

Addressed an issue where the Name field of the Logical Drive under MR controller page might be missing or changed unintentionally after exiting and going back to the MR controller page.

Known Issues:

None]]> Important Notes:

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system may encounter RSOD and fail to update firmware while performing firmware update.

Known Issues:

None]]> This product now supports Red Hat Enterprise Linux 9.5.

]]> This product fixes the kernel compilation issue.

]]> This product fixes warning message: index 1 is out of range.

]]>

This product fixes an issue where the speed may be downgraded to Gen3.

This product fixes an issue where the Linux driver fails to load due to an EEPROM checksum error when the RDE:MACAddress property is patched.

This product fixes an issue where the NIC is not detected after performing the RDE patch operation on NetworkDeviceFunctions settings.

This product fixes an issue where the RDE: Setting property (AutoSpeedNegotiationEnabled) does not cause the property value to update, returning a code 400.

This product fixes an issue where the RDE fails to perform the get operation when the adapter is configured as pass-through.

This product fixes an issue where the RDE property (FlowControlStatus) does not report the correct status after the RDE property FlowControlConfiguration is set to Tx.

This product fixes an issue where the RDE patch operation fails on the AutoSpeedNegotiationEnabled property.

]]> Add new support platform.

]]>

Added support for RHEL 10.

]]>

Fixed flashing issue through SDR method

]]> Important Notes:

This version of the Server Platform Services (SPS) Firmware contains updates aligned with the Intel Product Update (IPU) version IPU 2025.1 guidance. This version of the SPS 04.04.04.702 (2.30_01_06_2025) should be paired with System ROM 2.30 (01/16/2025) or later.

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Enhancements/New Features:

This version is in compliance with IPU 2025.1 guidance.

Known Issues:

None]]> This version is in compliance with IPU.2024.1 guidance.

]]> Important Notes:

Firmware Dependencies:

None

Problems Fixed:

This revision of the Server Platform Services Firmware provides mitigations for security vulnerability documented as CVE-2023-35191. This issue is not unique to HPE servers.

Known Issues:

None]]>

Added support for RHEL10.

]]>

Fixes the potential drive hang issue after POH exceed 6.5 years. We suggest customers to update the FW as soon as possible to prevent inconvenience.

For more information, CB is published at the following URL: https://support.hpe.com/hpesc/public/docDisplay?docId=a00142174en_us

]]> See the AMS Release Notes for information about the enhancements in this release.

]]> See the AMS Release Notes for information about the issues resolved in this release

]]> SR 2.9.2/SR 3.4.2 RC

]]>

Fixed an issue where the driver incorrectly handled multi-path failover.

Fixed an issue where the driver could hang under heavy I/O load.

]]> Updated multi-language translation.

Removed Expired SUSE and Vmware Certificates.

]]> Important Notes:

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the Name field of the Logical Drive under MR controller page might be missing or changed unintentionally after exiting and going back to the MR controller page.

Known Issues:

None]]> Added pop-up message for all Intelligent Provisioning boot paths to warn users of the risk of data loss.

]]> Important Notes:

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system iLO remote console might hang when the System Utilities Language is set to Japanese.

Known Issues:

None

]]> No changes or new features have been included in version 20.43.2026.

]]> The following issues have been fixed in version 20.43.2026:

A linkup issue vs a 3rd party switch (BCM53405).
A reference counter issue that resulted in the firmware assertion 0x889f with CQ reference counter underflow to solve a race condition.

]]> Security Hardening Enhancements: This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your device's firmware to this release to improve the firmware security and reliability of your device.

New features and changes included in version 20.43.1014:

Added the option to indicate an error CQE event on every selected function per eSwitch manager. This indication is defined as a new WQE including the relevant information about the error (such as: syndrome, function_id, timestamp, QPs num etc.).
Extended kernel lockdown permission set. The following sub-operations can now be called by tools (permission TOOLS_RESORCES) using new HCA capability bitmask field: tool_partial_cap.

The 5 sub-operations are:

QUERY_HCA_CAP with other function
QUERY_VUID with direct data
QUERY_ROCE_ADDRESS with other vport
SET_HCA_CAP with other function
POSTPONE_CONNECTED_QP_TIMEOUT with other vport

The new added caps are:

tool_partial_cap.postpone_conn_qp_timeout_other_vport,
tool_partial_cap.set_hca_cap_other_func
tool_partial_cap.query_roce_addr_other_vport
tool_partial_cap.query_vuid_direct_data
tool_partial_cap.query_hca_cap_other_func

]]> The following issues have been fixed in version 20.43.1014:

Setup crash when "create_sq" used invalid mbox.
The firmware always returned the "next" value to be applied when querying FACTORY default NV configuration values.

]]>

Added support for Azure Stack HCI 23H2.

]]>

Fix the controller library compatible issue.

]]>

Support new Gen12 servers.

]]>

Support new Gen12 servers.

Support new OS Azure Stack HCI 23H2 .

]]> Important Notes:

Firmware Dependencies:

None

Problems Fixed:

Known Issues:

None

]]> Important Notes:

None

Firmware Dependencies:

None

Problems Fixed:

Known Issues:

None

]]> See the AMS Release Notes for information about the enhancements in this release.

]]> See the AMS Release Notes for information about the issues resolved in this release.

]]> See the AMS Release Notes for information about the enhancements in this release.

]]> See the AMS Release Notes for information about the issues resolved in this release.

]]> Updated multi-language translation.

]]> Important Notes:

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where system may hang at POST when there are 8TB system memory and E810 NIC card installed.

Addressed an issue where the Name field of the Logical Drive under MR controller page might be missing or changed unintentionally after exiting and going back to the MR controller page.

Known Issues:

None]]> Important Notes:

Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the system may encounter RSOD and fail to update firmware while performing firmware update.

Known Issues:

None]]>

Added support for Azure Stack HCI 23H2.

]]>

Fixes the logic bug in the media cache cleaning abort handling that caused the drive to choose and execute the R/W command before the Request Sense to prevent assert.

Adding other logging and FW enhancements.

]]>

Added support for ESXi 9.0

]]>

Fix contains code improvements for SMART reporting.

]]>

DMTF PLDM Redfish Device Enablement enhancements: Add support for Redfish Encryption (POST & PATCH)

o POST Storage.SetEncryptionKey

o PATCH Storage[EncryptionMode]

o PATCH/POST Volume[Encrypted]

Note: MR controller support SED only. Therefore, Volume[EncryptionTypes] is not writeable during POST (Create) or PATCH (Update). Correspondingly the following Annotations are not populated:

a. EncryptionTypes@Redfish.AllowableValues (Volume Schema)

b. @Redfish.WriteableProperties[EncryptionTypes] (Volume Schema)

c. EncryptionTypes@Redfish.OptionalOnCreate (Volume Capabilities)

d. EncryptionTypes@Redfish.AllowableValues (Volume Capabilities)

e. EncryptionTypes@Redfish.UpdatableAfterCreate (Volume Capabilities)

o POST Volume.ForceEnable

o POST Drive.RevertToOriginalFactoryState

o Note:

PATCH Volume[Encrypted] can be issued only with option ‘true’ on eligible volumes. PATCH Volume[Encrypted] with option ‘false’ will befailed because a secure volume cannot be changed to an unsecurevolume in MR firmware.
During POST (Create) ‘Encrypted’ option is not allowed for creating a volume with RAIDType=None. This is because MR does not support creating a secure JBOD in one step. After creating the JBOD, PATCH Volume [Encrypted = true] can be issued to create a secure JBOD.
Whenever user requests to change to EKM, a reboot is a must to obtain the key via UEFI driver.

Add MR408i-p support
Added support for UBM10 backplanes
Support UBM backplane FW version display and FW update when UBM controller is in bootloader state if there is an interruption during FW update
Support NVMe SSD for Unmap capable Logical Drive. Please note that SATA SSD is not supported for Unmap capable Logical Drive.
NAND flash refresh improvements

o The algorithm that posts the event "System reset required" after a specified number of days has been removed. The refresh happens after the same specified time and the new events are populated as below:

Before starting the Nand flash refresh: “NAND refresh in progress:changing WB Logical Drives to WT”
After the completion of Nand flash refresh: “NAND refresh complete:changing WT virtual disks to WB”
The above behaviors are applicable only to MR400 controllers and arenot applicable to MR200 controllers
RAID1 Consistency Check Event String Change

o The Event String has been changed from "Consistency Check found inconsistent parity on LD <Ld Id> at strip <Strip Number>" to "Consistency Check found inconsistency on LD <Ld Id> at strip <Strip Number>".

Support a new controller property, "Spin Down Drives At Shutdown", to control spindown of configured drives during shutdown
Support for SCSI NVMe Translation Layer Specification version 1.14

]]>

Fix a00143232en_us: HPE MR Gen11 Controllers - The Component Integrity Status Is Shown As Not Supported in HPE ProLiant DL365/DL385 Gen11 Servers With AMD EPYC 9xx5 2P Configurations

Fix a00144054en_us: HPE MR Gen10 Plus and Gen11 Storage Controllers - Updating the SAS/SATA/NVMe Drive Firmware May Not Succeed When the System Boots to the VMware ESXi Operating System

Fix a00142857en_us: HPE MegaRAID Storage Administrator (MRSA) - Unexpected Information Displays in the HPE MRSA When Heavy I/Os Are Active

Fix an issue that CM7 FIPS drives are not identified as SED capable drives. CM7 FIPSdrive Model Number: VO001920YXUHU,VO003840YXUHV,VO007680YXUJA,MO001600YXUJB, MO003200YXUJC, MO006400YXUJD, VV007680LYJKF,VV015360LYXMT, MV003200LYJKH, MV006400LYJKK.

Fix an issue that foreign drives import with invalid security key with 5 attempts causing controller into infinite loop

Fix an issue that controller may assert when there is MCTP traffic when PCI BAR update is in progress

Fix an issue that Redfish Drive.CapableSpeedGbs shows as 22 instead of 22.5 for SAS4 drive

Fix an issue that the number of logical drives created is less than the expected when creating multiple Logical Drive in the same command with ReuseTargetId option

Fix an intermittent issue that pinned cache may not generate in multiple logical drive Config

Fix a rare issue that offline drive firmware download timed out due to host taskmanagement but still generate download complete event

Fix an issue that RAID5/50/6/60 logical drive performance may be lower when there is cache offload happened before server bootup

Fix an issue that controller may fault and recovery with OCR (online controller reset) while running Patrol Read on NVMe drives

Fix an issue that Maximum Write Same Length or Maximum Unmap Block Descriptor Count of NVMe JBOD drive may be overwritten and cause SCSI UNMAP or WRITE SAME command failed

Fix a rare issue that UR (Unsupported Request) for PCIe Memory Read may occur when host configure PCIe BAR at run-time

Fix an issue that SCSI UNMAP command using a parameter list length greater than 0 and less than 8 would fail with SCSI Sense key Illegal Request and Additional sense data of Invalid Field in Parameter List

Fix a rare issue that controller may assert because PCI bar initialization timeouts waiting for boot message processing

]]>

DMTF PLDM Redfish Device Enablement enhancements: Add support for Redfish Encryption (POST & PATCH)

o POST Storage.SetEncryptionKey

o PATCH Storage[EncryptionMode]

o PATCH/POST Volume[Encrypted]

Note: MR controller support SED only. Therefore, Volume[EncryptionTypes] is not writeable during POST (Create) or PATCH (Update). Correspondingly the following Annotations are not populated:

a. EncryptionTypes@Redfish.AllowableValues (Volume Schema)

b. @Redfish.WriteableProperties[EncryptionTypes] (Volume Schema)

c. EncryptionTypes@Redfish.OptionalOnCreate (Volume Capabilities)

d. EncryptionTypes@Redfish.AllowableValues (Volume Capabilities)

e. EncryptionTypes@Redfish.UpdatableAfterCreate (Volume Capabilities)

o POST Volume.ForceEnable

o POST Drive.RevertToOriginalFactoryState

o Note:

PATCH Volume[Encrypted] can be issued only with option ‘true’ on eligible volumes. PATCH Volume[Encrypted] with option ‘false’ will befailed because a secure volume cannot be changed to an unsecurevolume in MR firmware.
During POST (Create) ‘Encrypted’ option is not allowed for creating a volume with RAIDType=None. This is because MR does not support creating a secure JBOD in one step. After creating the JBOD, PATCH Volume [Encrypted = true] can be issued to create a secure JBOD.
Whenever user requests to change to EKM, a reboot is a must to obtain the key via UEFI driver.

Add MR408i-p support
Added support for UBM10 backplanes
Support UBM backplane FW version display and FW update when UBM controller is in bootloader state if there is an interruption during FW update
Support NVMe SSD for Unmap capable Logical Drive. Please note that SATA SSD is not supported for Unmap capable Logical Drive.
NAND flash refresh improvements

Before starting the Nand flash refresh: “NAND refresh in progress:changing WB Logical Drives to WT”
After the completion of Nand flash refresh: “NAND refresh complete:changing WT virtual disks to WB”
The above behaviors are applicable only to MR400 controllers and arenot applicable to MR200 controllers
RAID1 Consistency Check Event String Change

Support a new controller property, "Spin Down Drives At Shutdown", to control spindown of configured drives during shutdown
Support for SCSI NVMe Translation Layer Specification version 1.14