New features and changes included in version 22.46.3048:

  • Added support for RSS with crypto offload enabling the NIC to parallelize packet processing across CPU cores while performing encryption/decryption in hardware. Additionally, introduced a new l4_type_ext parameter with values: 0 (None), 1 (TCP), 2 (UDP), 3 (ICMP).
  • Added an extra validation for the payload_len field in incoming NC-SI messages. Previously, invalid packets might have been accepted; now, such packets are silently dropped.
  • This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your devices firmware to this release to improve the devices’ firmware security and reliability.

 

]]> New features and changes included in version 22.46.3048:

  • Added support for RSS with crypto offload enabling the NIC to parallelize packet processing across CPU cores while performing encryption/decryption in hardware. Additionally, introduced a new l4_type_ext parameter with values: 0 (None), 1 (TCP), 2 (UDP), 3 (ICMP).
  • Added an extra validation for the payload_len field in incoming NC-SI messages. Previously, invalid packets might have been accepted; now, such packets are silently dropped.
  • This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your devices firmware to this release to improve the devices’ firmware security and reliability.

 

]]> The following issues have been fixed in version 22.46.3048:

  • Configuring a small MTU led to fragmentation of packets critical for the PXE boot process. As a result, the PXE boot filters mistakenly discarded these packets, causing the PXE boot to fail.

 

]]> The following issues have been fixed in version 22.46.3048:

  • Configuring a small MTU led to fragmentation of packets critical for the PXE boot process. As a result, the PXE boot filters mistakenly discarded these packets, causing the PXE boot to fail.

 

]]> See the iSUT Release Notes for information about the issues resolved in this release

]]> See the iSUT Release Notes for information about the issues resolved in this release

]]> See the iSUT Release Notes for information about the issues resolved in this release

]]> See the iSUT Release Notes for information about the issues resolved in this release

]]> New features and changes included in version 26.46.3048:

  • Added support for RSS with crypto offload enabling the NIC to parallelize packet processing across CPU cores while performing encryption/decryption in hardware. Additionally, introduced a new l4_type_ext parameter with values: 0 (None), 1 (TCP), 2 (UDP), 3 (ICMP).
  • Added an extra validation for the payload_len field in incoming NC-SI messages. Previously, invalid packets might have been accepted; now, such packets are silently dropped.
  • This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your devices firmware to this release to improve the devices’ firmware security and reliability.
]]> New features and changes included in version 26.46.3048:

  • Added support for RSS with crypto offload enabling the NIC to parallelize packet processing across CPU cores while performing encryption/decryption in hardware. Additionally, introduced a new l4_type_ext parameter with values: 0 (None), 1 (TCP), 2 (UDP), 3 (ICMP).
  • Added an extra validation for the payload_len field in incoming NC-SI messages. Previously, invalid packets might have been accepted; now, such packets are silently dropped.
  • This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your devices firmware to this release to improve the devices’ firmware security and reliability.
]]> The following issues have been fixed in version 26.46.3048:

  • Configuring a small MTU led to fragmentation of packets critical for the PXE boot process. As a result, the PXE boot filters mistakenly discarded these packets, causing the PXE boot to fail.

 

 

]]> The following issues have been fixed in version 26.46.3048:

  • Configuring a small MTU led to fragmentation of packets critical for the PXE boot process. As a result, the PXE boot filters mistakenly discarded these packets, causing the PXE boot to fail.

 

 

]]>
  • HPK6 is a planned maintenance release that follows the HPK3 FW release for 30.72TB (8K IU) Solid State Drive. This is a recommended FW release.
  • For more information, refer to HPE Customer Advisory at the following URL: https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-a00150459en_us
    • ]]>
  • HPK6 is a planned maintenance release that follows the HPK3 FW release for 30.72TB (8K IU) Solid State Drive. This is a recommended FW release.
  • For more information, refer to HPE Customer Advisory at the following URL: https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-a00150459en_us
    • ]]>
  • This FW update contains the fix for false ILO message of temporary drive "degraded" status.
    • ]]>
  • This FW update contains the fix for false ILO message of temporary drive "degraded" status.
    • ]]>         New features and changes included in version 22.46.3048:

    • Added support for RSS with crypto offload enabling the NIC to parallelize packet processing across CPU cores while performing encryption/decryption in hardware. Additionally, introduced a new l4_type_ext parameter with values: 0 (None), 1 (TCP), 2 (UDP), 3 (ICMP).
    • Added an extra validation for the payload_len field in incoming NC-SI messages. Previously, invalid packets might have been accepted; now, such packets are silently dropped.
    • This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your devices firmware to this release to improve the devices’ firmware security and reliability.

     

     

    ]]>         New features and changes included in version 22.46.3048:

    • Added support for RSS with crypto offload enabling the NIC to parallelize packet processing across CPU cores while performing encryption/decryption in hardware. Additionally, introduced a new l4_type_ext parameter with values: 0 (None), 1 (TCP), 2 (UDP), 3 (ICMP).
    • Added an extra validation for the payload_len field in incoming NC-SI messages. Previously, invalid packets might have been accepted; now, such packets are silently dropped.
    • This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your devices firmware to this release to improve the devices’ firmware security and reliability.

     

     

    ]]>         The following issues have been fixed in version 22.46.3048:

    • Configuring a small MTU led to fragmentation of packets critical for the PXE boot process. As a result, the PXE boot filters mistakenly discarded these packets, causing the PXE boot to fail.

     

     

    ]]>         The following issues have been fixed in version 22.46.3048:

    • Configuring a small MTU led to fragmentation of packets critical for the PXE boot process. As a result, the PXE boot filters mistakenly discarded these packets, causing the PXE boot to fail.

     

     

    ]]>
  • RSOD issue fixed. RSOD was occurred during server power-on if enable the VROC.
    • ]]>
  • RSOD issue fixed. RSOD was occurred during server power-on if enable the VROC.
    • ]]>         Important Notes:

    Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

    Firmware Dependencies:

    None

    Problems Fixed:

    Addressed an issue which prevented the installation of RHEL 9.7 and RHEL 10.1 when Secure Boot is enabled.

    Known Issues:

    None]]>         Important Notes:

    Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

    Firmware Dependencies:

    None

    Problems Fixed:

    Addressed an issue which prevented the installation of RHEL 9.7 and RHEL 10.1 when Secure Boot is enabled.

    Known Issues:

    None]]>         DIMMのシリアル番号が無効な場合にエラーログが強化されました。

    ]]>         Enhanced error logging when the DIMM serial number is invalid.

    ]]>         重要な注意：

    報告されたセキュリティ脆弱性とその緩和策の詳細については、リンクセキュリティ報告ライブラリ | HPEサポートを参照してください。

    ファームウェアの依存関係：

    なし

    修正された問題：

    RBSUでVLAN構成が有効になっている場合に、VLANタグがUEFIネットワークデバイスパスに追加されない問題に対処しました。

    既知の問題点：

    なし]]>         Important Notes:

    Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

    Firmware Dependencies:

    None

    Problems Fixed:

    Addressed an issue where the VLAN tag is not added to the UEFI network device path when the VLAN configuration is enabled in RBSU.

    Known Issues:

    None]]>
  • RSOD issue fixed. RSOD was occurred during server power-on if enable the VROC.
    • ]]>
  • RSOD issue fixed. RSOD was occurred during server power-on if enable the VROC.
    • ]]>
  • RSOD issue fixed. RSOD was occurred during server power-on if enable the VROC.
    • ]]>
  • RSOD issue fixed. RSOD was occurred during server power-on if enable the VROC.
    • ]]>
  • Fix for Uncorrectable Machine Check Exception (UMCE) issue which might occur.
    • ]]>
  • Fix for Uncorrectable Machine Check Exception (UMCE) issue which might occur.
    • ]]>         AMS qualification of HPE ProLiant Compute DL384 Gen12 Server

    ]]>         AMS qualification of HPE ProLiant Compute DL384 Gen12 Server

    ]]>         Fix for amsd crashing upon hot-add/remove of non-nvme local drives.

    ]]>         Fix for amsd crashing upon hot-add/remove of non-nvme local drives.

    ]]>
  • Support Gen12 servers.
    • ]]>
  • Support Gen12 servers.
    • ]]>         For Gen11 PR3 & 2023 March MSB

    ]]>         For Gen11 PR3 & 2023 March MSB

    ]]>         New features and changes included in version 26.46.3048:

    • Added support for RSS with crypto offload enabling the NIC to parallelize packet processing across CPU cores while performing encryption/decryption in hardware. Additionally, introduced a new l4_type_ext parameter with values: 0 (None), 1 (TCP), 2 (UDP), 3 (ICMP).
    • Added an extra validation for the payload_len field in incoming NC-SI messages. Previously, invalid packets might have been accepted; now, such packets are silently dropped.
    • This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your devices firmware to this release to improve the devices’ firmware security and reliability.

     

    ]]>         New features and changes included in version 26.46.3048:

    • Added support for RSS with crypto offload enabling the NIC to parallelize packet processing across CPU cores while performing encryption/decryption in hardware. Additionally, introduced a new l4_type_ext parameter with values: 0 (None), 1 (TCP), 2 (UDP), 3 (ICMP).
    • Added an extra validation for the payload_len field in incoming NC-SI messages. Previously, invalid packets might have been accepted; now, such packets are silently dropped.
    • This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your devices firmware to this release to improve the devices’ firmware security and reliability.

     

    ]]>         The following issues have been fixed in version 26.46.3048:

    • Configuring a small MTU led to fragmentation of packets critical for the PXE boot process. As a result, the PXE boot filters mistakenly discarded these packets, causing the PXE boot to fail.

     

    ]]>         The following issues have been fixed in version 26.46.3048:

    • Configuring a small MTU led to fragmentation of packets critical for the PXE boot process. As a result, the PXE boot filters mistakenly discarded these packets, causing the PXE boot to fail.

     

    ]]>
  • HPK8 is a planned maintenance release that follows HPK5. This is a recommended FW release that provides bug fixes for the P5430 15.36T, 7.68T, 3.84T (4K IU) Solid State Drives.
    • ]]>
  • HPK8 is a planned maintenance release that follows HPK5. This is a recommended FW release that provides bug fixes for the P5430 15.36T, 7.68T, 3.84T (4K IU) Solid State Drives.
    • ]]>
  • Regular FW maintenance release for sanitize, DRAM,DMA transfer and log page fix.
    • ]]>
  • Regular FW maintenance release for sanitize, DRAM,DMA transfer and log page fix.
    • ]]>
  • The FW address: PCIe link drop and 0ther regular FW patches release.
    • ]]>
  • The FW address: PCIe link drop and 0ther regular FW patches release.
    • ]]>         New features and changes included in version 26.46.3048:

    • Added support for RSS with crypto offload enabling the NIC to parallelize packet processing across CPU cores while performing encryption/decryption in hardware. Additionally, introduced a new l4_type_ext parameter with values: 0 (None), 1 (TCP), 2 (UDP), 3 (ICMP).
    • Added an extra validation for the payload_len field in incoming NC-SI messages. Previously, invalid packets might have been accepted; now, such packets are silently dropped.
    • This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your devices firmware to this release to improve the devices’ firmware security and reliability.

     

     

    ]]>         New features and changes included in version 26.46.3048:

    • Added support for RSS with crypto offload enabling the NIC to parallelize packet processing across CPU cores while performing encryption/decryption in hardware. Additionally, introduced a new l4_type_ext parameter with values: 0 (None), 1 (TCP), 2 (UDP), 3 (ICMP).
    • Added an extra validation for the payload_len field in incoming NC-SI messages. Previously, invalid packets might have been accepted; now, such packets are silently dropped.
    • This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your devices firmware to this release to improve the devices’ firmware security and reliability.

     

     

    ]]>         The following issues have been fixed in version 26.46.3048:

    • Configuring a small MTU led to fragmentation of packets critical for the PXE boot process. As a result, the PXE boot filters mistakenly discarded these packets, causing the PXE boot to fail.

     

    ]]>         The following issues have been fixed in version 26.46.3048:

    • Configuring a small MTU led to fragmentation of packets critical for the PXE boot process. As a result, the PXE boot filters mistakenly discarded these packets, causing the PXE boot to fail.

     

    ]]>
  • The FW address: PCIe link drop and 0ther regular FW patches release.
    • ]]>
  • The FW address: PCIe link drop and 0ther regular FW patches release.
    • ]]>
  • HPK8 is a planned maintenance release that follows HPK5. This is a recommended FW release that provides bug fixes for the P5430 15.36T, 7.68T, 3.84T (4K IU) Solid State Drives.
    • ]]>
  • HPK8 is a planned maintenance release that follows HPK5. This is a recommended FW release that provides bug fixes for the P5430 15.36T, 7.68T, 3.84T (4K IU) Solid State Drives.
    • ]]>         • Updated SNMP MIBKIT to add additional storage controller properties and value set.

    • Added new root CA for Micron Drives in iLO for all models from the 7600 series onward.

    • Enabled secure erase of a single NVMe direct attached drive using Redfish API.

    • Enabled RTX600D Pro Accelerator support in iLO6 firmware for HPE ProLiant DL385 Gen11 Platforms.

    • Enabled RTX4500 Accelerator support in iLO6 firmware for HPE ProLiant DL385 Gen11 Platforms.

    • Added support for AMD Instinct MI355X firmware update on HPE ProLiant Compute XD685.

    ]]>         • Updated SNMP MIBKIT to add additional storage controller properties and value set.

    • Added new root CA for Micron Drives in iLO for all models from the 7600 series onward.

    • Enabled secure erase of a single NVMe direct attached drive using Redfish API.

    • Enabled RTX600D Pro Accelerator support in iLO6 firmware for HPE ProLiant DL385 Gen11 Platforms.

    • Enabled RTX4500 Accelerator support in iLO6 firmware for HPE ProLiant DL385 Gen11 Platforms.

    • Added support for AMD Instinct MI355X firmware update on HPE ProLiant Compute XD685.

    ]]>         • Fixed the mismatch in Virtual Serial Port (VSP) Enabled state value between Redfish and iLO Command Line Interface (CLI) (/system1/oemHPE_vsp1).

    • Fixed an issue by adding the handling of EAP packet with Identifier Value 0 in iLO.

    • Fixed a file descriptor leak in iLO CLI.

    • Fixed an issue where iLO is taking 20-30 minutes to be accessible after Aux Power Cycle during a firmware flash on HPE ProLiant Compute XD685 with NVIDIA H200 GPU trays.

    • Fixed an issue where NVIDIA HGX PCIe Switch versions are not being displayed on HPE ProLiant Compute XD685 with NVIDIA H200 GPU trays.

    • Fixed issues with auxiliary power reset not working properly on AMD Instinct platforms on HPE ProLiant Compute XD685.

    • Improved firmware update progress percentage when flashing NVIDIA HGX GPU or AMD Instinct GPU firmware packages on HPE ProLiant Compute XD685.

    • Fixed issues with GPU management failing to work after firmware update on HPE ProLiant Compute XD685 with AMD Instinct MI355X GPUs.

    • Fixed issues with AMD Pensando Pollara 400 AI NIC firmware version getting partially truncated on iLO Firmware Inventory page.

    ]]>         • Fixed the mismatch in Virtual Serial Port (VSP) Enabled state value between Redfish and iLO Command Line Interface (CLI) (/system1/oemHPE_vsp1).

    • Fixed an issue by adding the handling of EAP packet with Identifier Value 0 in iLO.

    • Fixed a file descriptor leak in iLO CLI.

    • Fixed an issue where iLO is taking 20-30 minutes to be accessible after Aux Power Cycle during a firmware flash on HPE ProLiant Compute XD685 with NVIDIA H200 GPU trays.

    • Fixed an issue where NVIDIA HGX PCIe Switch versions are not being displayed on HPE ProLiant Compute XD685 with NVIDIA H200 GPU trays.

    • Fixed issues with auxiliary power reset not working properly on AMD Instinct platforms on HPE ProLiant Compute XD685.

    • Improved firmware update progress percentage when flashing NVIDIA HGX GPU or AMD Instinct GPU firmware packages on HPE ProLiant Compute XD685.

    • Fixed issues with GPU management failing to work after firmware update on HPE ProLiant Compute XD685 with AMD Instinct MI355X GPUs.

    • Fixed issues with AMD Pensando Pollara 400 AI NIC firmware version getting partially truncated on iLO Firmware Inventory page.

    ]]>         • 電源センサープロパティPowerCapacityWattsを、RinlineサーバーのReadingUnitsプロパティの読み取りと追加によって置換できるようにしました。
    • HPE ProLiant Gen 11サーバー上のHPE iLO GUIによるSPDMデバイスの証明書管理と機能強化された測定のサポート。
    • デフォルトでVSPが有効になりました。
    • ML/DLサーバーのシステムエネルギー消費カウンターをレポートするようにサポートします。
    • ESKMサーバーのKMIP (Key Management Interoperability Protocol) リモートキー管理方式のサポート。

    ]]>         • Enabled the replacement of the power-sensor property PowerCapacityWatts with Reading and adding the ReadingUnits property for Rinline server.
    • Support for certificate management and enhanced measurements for SPDM devices through HPE iLO GUI on HPE ProLiant Gen 11 servers.
    • Enabled VSP by default.
    • Support to report system energy consumption counter for ML/DL servers.
    • Support for Key Management Interoperability Protocol (KMIP) remote key management method for ESKM server.

    ]]>         • 選択されていないグローバルコンポーネントの完全性オプションセットで、コンポーネントの完全性ポリシーメニューがグレー表示にならない問題を修正しました。
    • /redfish/v1/Systems/1/LogServices/Event/Entriesを使用したHPE iLOイベントの読み取り中に、AggregateHealthStatusChangeイベントで報告されていた空のメッセージ引数を修正しました。
    • サーバーブートが完了した後でも、HPE iLOがInPostDiscoveryCompleteを報告できない問題を修正しました。
    •権限が不十分なHPE iLO 6ユーザーがまだVSPコマンドを実行できる問題を修正しました。
    • 複数のコンソールからSNMPWALKを並列で実行すると、HPE iLO SNMPが応答しなくなる問題を修正しました。
    • ストレージ条件が失敗した場合にSNMPが適切な出力を表示できない問題を修正しました。
    • ユーザーがHPE iLOを使用して、HPE ProLiant DL365 Gen11サーバーのSSDファームウェアをアップデートできない問題を修正しました。
    • ストレージサブシステムのヘルス状態を含めて考慮するように、SNMP OID cpqHeMibConditionを修正しました。

    ]]>         • Fixed an issue where the Component Integrity Policy menu was not grayed out with an unselected Global Component Integrity option set.
    • Fixed the empty message arguments that were reported with AggregateHealthStatusChange event while reading HPE iLO events using /redfish/v1/Systems/1/LogServices/Event/Entries.
    • Fixed an issue where HPE iLO failed to report InPostDiscoveryComplete even after server boot is completed.
    • Fixed an issue where an HPE iLO 6 user with insufficient privilege was still able to run VSP commands.
    • Fixed an issue where HPE iLO SNMP became unresponsive when SNMPWALK ran in parallel from multiple consoles.
    • Fixed an issue with SNMP failed to display a proper output when storage condition is failed.
    • Fixed an issue where a user was unable to update the SSD firmware for HPE ProLiant DL365 Gen11 server using HPE iLO.
    • Fixed the SNMP OID cpqHeMibCondition to include and account for the Storage subsystem health condition.

    ]]>         AMS qualification of HPE ProLiant Compute DL384 Gen12 Server

    ]]>         AMS qualification of HPE ProLiant Compute DL384 Gen12 Server

    ]]>         Fix for amsd crashing upon hot-add/remove of non-nvme local drives.

    ]]>         Fix for amsd crashing upon hot-add/remove of non-nvme local drives.

    ]]>
  • Firmware maintenance release.
    • ]]>
  • Firmware maintenance release.
    • ]]>
  • Changes and improvements which disable MCTP over PCIe VDM over the previous firmware.
    • ]]>
  • Changes and improvements which disable MCTP over PCIe VDM over the previous firmware.
    • ]]>         HPE ProLiant Compute DL384 Gen12サーバーのAMS認定

    ]]>         AMS qualification of HPE ProLiant Compute DL384 Gen12 Server

    ]]>         非NVMeローカルドライブのホットアド/リムーブ時にamsdがクラッシュする問題を修正。

    ]]>         Fix for amsd crashing upon hot-add/remove of non-nvme local drives.

    ]]>
  • Regular FW maintenance release for sanitize, DRAM,DMA transfer and log page fix.
    • ]]>
  • Regular FW maintenance release for sanitize, DRAM,DMA transfer and log page fix.
    • ]]>         非NVMeローカルドライブのホットアド/リムーブ時にamsdがクラッシュする問題を修正。

    ]]>         Fix for amsd crashing upon hot-add/remove of non-nvme local drives.

    ]]>
  • Previous firmware version HPK5 may cause Uncorrectable Machine Check Exception (UMCE) to occur. It is recommended to update firmware version to HPK6.
  • For more information, CA is published at the following URL: https://support.hpe.com/hpesc/public/docDisplay?docId=a00142315en_us
    • ]]>
  • Previous firmware version HPK5 may cause Uncorrectable Machine Check Exception (UMCE) to occur. It is recommended to update firmware version to HPK6.
  • For more information, CA is published at the following URL: https://support.hpe.com/hpesc/public/docDisplay?docId=a00142315en_us
    • ]]>         New features and changes included in version 26.46.3048:

    • Added support for RSS with crypto offload enabling the NIC to parallelize packet processing across CPU cores while performing encryption/decryption in hardware. Additionally, introduced a new l4_type_ext parameter with values: 0 (None), 1 (TCP), 2 (UDP), 3 (ICMP).
    • Added an extra validation for the payload_len field in incoming NC-SI messages. Previously, invalid packets might have been accepted; now, such packets are silently dropped.
    • This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your devices firmware to this release to improve the devices’ firmware security and reliability.
    ]]>         New features and changes included in version 26.46.3048:

    • Added support for RSS with crypto offload enabling the NIC to parallelize packet processing across CPU cores while performing encryption/decryption in hardware. Additionally, introduced a new l4_type_ext parameter with values: 0 (None), 1 (TCP), 2 (UDP), 3 (ICMP).
    • Added an extra validation for the payload_len field in incoming NC-SI messages. Previously, invalid packets might have been accepted; now, such packets are silently dropped.
    • This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your devices firmware to this release to improve the devices’ firmware security and reliability.
    ]]>         The following issues have been fixed in version 26.46.3048:

    • Configuring a small MTU led to fragmentation of packets critical for the PXE boot process. As a result, the PXE boot filters mistakenly discarded these packets, causing the PXE boot to fail.

     

    ]]>         The following issues have been fixed in version 26.46.3048:

    • Configuring a small MTU led to fragmentation of packets critical for the PXE boot process. As a result, the PXE boot filters mistakenly discarded these packets, causing the PXE boot to fail.

     

    ]]>
  • Regular FW maintenance for fixing MCU,sanitize, DRAM and log page..etc.
    • ]]>
  • Regular FW maintenance for fixing MCU,sanitize, DRAM and log page..etc.
    • ]]>         Private release for specific customers.

    ]]>         Private release for specific customers.

    ]]>         SY480 Gen12 サーバーをサポートします。

    ]]>         Support SY480 Gen12 server.

    ]]>
  • HPK6 is a planned maintenance release that follows the HPK3 FW release for 30.72TB (8K IU) Solid State Drive. This is a recommended FW release.
  • For more information, refer to HPE Customer Advisory at the following URL: https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-a00150459en_us
    • ]]>
  • HPK6 is a planned maintenance release that follows the HPK3 FW release for 30.72TB (8K IU) Solid State Drive. This is a recommended FW release.
  • For more information, refer to HPE Customer Advisory at the following URL: https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-a00150459en_us
    • ]]>
  • Regular FW maintenance for fixing MCU,sanitize, DRAM and log page..etc.
    • ]]>
  • Regular FW maintenance for fixing MCU,sanitize, DRAM and log page..etc.
    • ]]>         今回のリリースで解決した問題については、iSUT Release Notesを参照してください。

    ]]>         See the iSUT Release Notes for information about the issues resolved in this release

    ]]>         今回のリリースで解決した問題については、iSUT Release Notesを参照してください。

    ]]>         See the iSUT Release Notes for information about the issues resolved in this release

    ]]>         今回のリリースで解決した問題については、iSUT Release Notesを参照してください。

    ]]>         See the iSUT Release Notes for information about the issues resolved in this release

    ]]>         今回のリリースで解決した問題については、iSUT Release Notesを参照してください。

    ]]>         See the iSUT Release Notes for information about the issues resolved in this release

    ]]>
  • Previous firmware version HPK5 may cause Uncorrectable Machine Check Exception (UMCE) to occur. It is recommended to update firmware version to HPK6.
  • For more information, CA is published at the following URL: https://support.hpe.com/hpesc/public/docDisplay?docId=a00142315en_us
    • ]]>
  • Previous firmware version HPK5 may cause Uncorrectable Machine Check Exception (UMCE) to occur. It is recommended to update firmware version to HPK6.
  • For more information, CA is published at the following URL: https://support.hpe.com/hpesc/public/docDisplay?docId=a00142315en_us
    • ]]>
  • This FW update contains the fix for false ILO message of temporary drive "degraded" status.
    • ]]>
  • This FW update contains the fix for false ILO message of temporary drive "degraded" status.
    • ]]>         HPE ProLiant Compute DL384 Gen12サーバーのAMS認定

    ]]>         AMS qualification of HPE ProLiant Compute DL384 Gen12 Server

    ]]>         非NVMeローカルドライブのホットアド/リムーブ時にamsdがクラッシュする問題を修正。

    ]]>         Fix for amsd crashing upon hot-add/remove of non-nvme local drives.

    ]]>         HPE ProLiant Compute DL384 Gen12サーバーのAMS認定

    ]]>         AMS qualification of HPE ProLiant Compute DL384 Gen12 Server

    ]]>         非NVMeローカルドライブのホットアド/リムーブ時にamsdがクラッシュする問題を修正。

    ]]>         Fix for amsd crashing upon hot-add/remove of non-nvme local drives.

    ]]>         Important Notes:

    Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

    Firmware Dependencies:

    None

    Problems Fixed:

    Addressed an issue which prevented the installation of RHEL 9.7 and RHEL 10.1 when Secure Boot is enabled.

    Known Issues:

    None

    ]]>         Important Notes:

    Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

    Firmware Dependencies:

    None

    Problems Fixed:

    Addressed an issue which prevented the installation of RHEL 9.7 and RHEL 10.1 when Secure Boot is enabled.

    Known Issues:

    None

    ]]>         Redesigned system cable routing detection for invalid configurations.

    ]]>         Redesigned system cable routing detection for invalid configurations.

    ]]>         Important Notes:

    Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

    Firmware Dependencies:

    None

    Problems Fixed:

    Resolved an issue where the UUID was missing after reconfiguring the NVMe-oF initiator name.

    Resolved an issue where the system hung during Power-On Self Test (POST) when running SUSE on NVMe-oF.

    Addressed an issue where the system hung during Power-On Self Test (POST) on configurations with 1xGH200/2EDSFF-Balance/2xPCIe Slots.

    Known Issues:

    None]]>         Important Notes:

    Details about reported security vulnerabilities and their mitigation can be found at the following link Security Bulletin Library | HPE Support.

    Firmware Dependencies:

    None

    Problems Fixed:

    Resolved an issue where the UUID was missing after reconfiguring the NVMe-oF initiator name.

    Resolved an issue where the system hung during Power-On Self Test (POST) when running SUSE on NVMe-oF.

    Addressed an issue where the system hung during Power-On Self Test (POST) on configurations with 1xGH200/2EDSFF-Balance/2xPCIe Slots.

    Known Issues:

    None]]>
  • Firmware maintenance release.
    • ]]>
  • Firmware maintenance release.
    • ]]>
  • RSOD issue fixed. RSOD was occurred during server power-on if enable the VROC.
    • ]]>
  • RSOD issue fixed. RSOD was occurred during server power-on if enable the VROC.
    • ]]>
  • Fix for Uncorrectable Machine Check Exception (UMCE) issue which might occur.
    • ]]>
  • Fix for Uncorrectable Machine Check Exception (UMCE) issue which might occur.
    • ]]>
  • Changes and improvements which disable MCTP over PCIe VDM over the previous firmware.
    • ]]>
  • Changes and improvements which disable MCTP over PCIe VDM over the previous firmware.
    • ]]>         HPE ProLiant Compute DL384 Gen12サーバーのAMS認定

    ]]>         AMS qualification of HPE ProLiant Compute DL384 Gen12 Server

    ]]>         非NVMeローカルドライブのホットアド/リムーブ時にamsdがクラッシュする問題を修正。

    ]]>         Fix for amsd crashing upon hot-add/remove of non-nvme local drives.

    ]]>         HPE ProLiant Compute DL384 Gen12サーバーのAMS認定

    ]]>         AMS qualification of HPE ProLiant Compute DL384 Gen12 Server

    ]]>         非NVMeローカルドライブのホットアド/リムーブ時にamsdがクラッシュする問題を修正。

    ]]>         Fix for amsd crashing upon hot-add/remove of non-nvme local drives.

    ]]>
  • 適切な操作と正確なデータ読み取りを保証するために DFC設定が改善されました。
  • 強化されたSES機能により、特定の設定は変更されません。
    • ]]>
  • Improved DFC settings to ensure proper operation and accurate data reading.
  • Enhanced SES functionality so certain settings remain unchanged.
    • ]]>
  • エラーを引き起こす可能性があるPWDISの問題を修正しました。
  • ベイ 11 および 12にドライブを追加するとリセットが発生したり、ドライブが見つからなくなったりする問題を解決しました。
    • ]]>
  • Fixed an issue with PWDIS that could cause errors.
  • Resolved a problem where adding drives to bays 11 and 12 caused resets or missing drives.
    • ]]>         新バージョン1.16

    ]]>         New vesion with 1.16

    ]]>